Digitala Vetenskapliga Arkivet

Change search
CiteExportLink to record
Permanent link

Direct link
Cite
Citation style
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Other style
More styles
Language
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Other locale
More languages
Output format
  • html
  • text
  • asciidoc
  • rtf
Design och utvärdering av AM-tillverkade omnidirektionella vindkraftverk: En jämförande studie av turbindesign samt utveckling av elektriskt DC system för småskalig produktutveckling.
Mid Sweden University, Faculty of Science, Technology and Media, Department of Engineering, Mathematics, and Science Education (2023-).
2025 (Swedish)Independent thesis Basic level (professional degree), 10 credits / 15 HE creditsStudent thesis
Abstract [sv]

Syftet med rapporten är att utveckla en liten vindturbin för småskalig användning åt Printit Sweden AB. Tre turbindesigner valdes ut baserat på tidigare studier och simulerades i Solidworks för att utvärdera om PLA, PETG eller ABS var lämpligast som tillverkningsmaterial. En litteraturstudie jämförde materialen med avseende på hållfasthet, slitage, UV-tålighet och miljöpåverkan.

Prototypen monterades med en växellåda på 1:240, men detta gav för högt motstånd. Utväxlingen justerades därför till 1:2,4. Elsystemet konstruerades med diodlikriktare, sensor (INA219) och Arduino Uno för att mäta spänning och strömstyrka. Systemet testades först med motordrift och därefter i vindtunnel med olika turbiner vid fem vindhastigheter 2,8–14 m/s.

Simuleringar visade att alla tre material har tillräcklig hållfasthet. Litteraturanalysen visade att PETG är bäst i UV-skyddade miljöer, medan PLA är mer UV-tåligt. Testerna visade att friktion och instabilitet i växellådan hindrade funktion, vilket löstes genom att byta till M10-gängstänger, kullager och minska utväxlingen.

Efter kortslutning i motorn kunde inte effekten mätas, men turbinerna jämfördes genom stopphastighet. Twisted och H-rotor presterade bäst och visade ingen signifikant skillnad mellan sig, men båda var signifikant bättre än 2-stegsturbinen.

För framtida utveckling föreslås en remväxel och en motor med fler lindningar för att minska energiförluster. H-rotor eller Twisted turbin rekommenderas, med PETG där UV-strålning ej förekommer och PLA där det gör det.

Abstract [en]

The aim of this report is to develop a small-scale wind turbine for Printit Sweden AB. Three turbine designs were selected based on previous studies and simulated in SolidWorks to evaluate the suitability of PLA, PETG, or ABS as manufacturing materials. A brief literature review compared these materials regarding durability, UV resistance, and environmental impact.

The initial prototype had a 1:240 gear ratio, which proved too high. This was adjusted to 1:2.4 for better functionality. A DC electrical system was built using a diode rectifier, INA219 sensor, and Arduino Uno for voltage and current logging. The system was tested with motor drive and in a wind tunnel at wind speeds from 2.8 to 14 m/s.

Simulations showed all three materials had adequate strength. The literacy study showed that PETG performed best in UV-protected environments, while PLA was more suitable under UV exposure. Early wind tunnel tests showed issues with friction and shaft instability, which were resolved by modifying the mechanical components and reducing the gear ratio.

Due to a motor short circuit, full power measurements couldn't be completed. Instead, turbine stop speeds were measured. The Twisted and H-rotor turbines performed best, with no significant difference between them, but both outperformed the two-stage turbine.

For future development, a belt drive and a multi-winding motor are recommended to reduce losses and improve voltage output. The H-rotor or Twisted turbine is advised, using PETG in shaded conditions and PLA for UV-exposed applications.

Place, publisher, year, edition, pages
2025. , p. 38
Keywords [en]
Average Power, Flow simulation, Additive manufacturing
Keywords [sv]
Medeleffekt, Flödessimulering, Additiv tillverkning
National Category
Other Mechanical Engineering
Identifiers
URN: urn:nbn:se:miun:diva-55071OAI: oai:DiVA.org:miun-55071DiVA, id: diva2:1982374
External cooperation
Printit Sweden AB
Educational program
Additiv tillverkning - högskoleingenjör maskinteknik THMTG 180 hp
Supervisors
Examiners
Available from: 2025-07-08 Created: 2025-07-08 Last updated: 2025-09-25Bibliographically approved

Open Access in DiVA

fulltext(1606 kB)47 downloads
File information
File name FULLTEXT01.pdfFile size 1606 kBChecksum SHA-512
2655b01b57c0ae3a519057e3a0e5a97617e6b88e6efb003ee0177f5e7f056928ad1e6f55c6e85a1072298c4bcc8a8717200f75ff80cd8290796f05ca85501102
Type fulltextMimetype application/pdf

Search in DiVA

By author/editor
Dadell, Pontus
By organisation
Department of Engineering, Mathematics, and Science Education (2023-)
Other Mechanical Engineering

Search outside of DiVA

GoogleGoogle Scholar
Total: 49 downloads
The number of downloads is the sum of all downloads of full texts. It may include eg previous versions that are now no longer available

urn-nbn

Altmetric score

urn-nbn
Total: 182 hits
CiteExportLink to record
Permanent link

Direct link
Cite
Citation style
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Other style
More styles
Language
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Other locale
More languages
Output format
  • html
  • text
  • asciidoc
  • rtf