Vibration-Induced Fatigue in Piping Systems
2025 (English)Independent thesis Advanced level (degree of Master (Two Years)), 20 credits / 30 HE credits
Student thesisAlternative title
Vibrationsinducerad utmattning i rörsystem (Swedish)
Abstract [en]
Vibration-induced fatigue in industrial piping is commonly assessed with the Energy Institute (EI) velocity diagram, a tool that is widely regarded as conservative, albeit not precisely quantified. This thesis investigates both the origin of the diagram and the degree of conservatism built into it, while also identifying the key parameters that practitioners should account for when using the method.
The work set out to reproduce the Energy Institute diagram using three progressively more detailed approaches: an analytical Euler–Bernoulli beam model, a beam-element FEA model, and a shell-element FEA model. From each model’s solutions the stress-velocity proportionality was extracted together with their respective eigenfrequency. By assigning the fatigue endurance limit as the target stress, representative of the weld fatigue classes F2 and D for the methods nominal stress and hot-spot respectively, a maximum allowable velocity was calculated.
For the analytical model and the beam model the maximum allowable velocity is approximately 110 mm/s RMS, independent of frequency. This value also coincides with the upper bound to the extracted velocities from the shell element model. Capturing the effects of flexible joints and heavy valves, the shell element model reveals a spread of data points of up to two orders of magnitude, with the greatest variation in the low-frequency range. The parameters identified to cause this variation were the valve-to-pipe mass ratio and the flexibility of the joint.
The results from the study indicate that the inclination of the categorization lines as well as the width of the “Concern” region of the EI diagram are the results of the non-idealistic beam properties, such as concentrated masses on the span and flexible joints. Statistical lower envelopes fitted to the data show that the Energy Institute Concern and Problem lines correspond closely to the twentieth and first percentiles, respectively, thereby covering about eighty and ninety-nine percent of realistic geometries.
The study confirms the guideline’s overall validity and proposes extending its applicability via scaling factors for weld quality, cross-section geometry, and very-high-cycle fatigue conditions.
Abstract [sv]
Vibrationsorsakad utmattning i industriella rörsystem är ofta utvärderade med Energy Institutes (EI) hastighetsdiagram, en metod som i allmänhet uppfattas som konservativt, men vars säkerhetsmarginaler ej exakt kvantifierade. Detta examensarbete undersöker både diagrammets härkomst och den inbyggda konservatismen samt identifierar de väsentliga parametrar som bör beaktas vid användning av metoden.
Arbetet syftade till att återskapa Energy Institute-diagrammet med tre successivt mer detaljerade angreppssätt: en analytisk modell baserad på teknisk balkteori, en balkelements-FEM-modell och en skal-FEM-modell. Ur varje modell extraherades sambandet mellan spänning och hastighet samt respektive egenfrekvens. Genom att sätta utmattningsgränsen som dimensionerande spänning, motsvarande svetsklasserna F2 (för nominell spänning) respektive D (för hot-spot-spänning), beräknades en maximalt tillåten hastighet.
För den analytiska modellen och balkelementmodellen erhölls en högsta tillåtna hastighet på cirka 110 mm/s RMS, oberoende av frekvens. Detta värde sammanfaller med den övre gränsen till de hastigheter som erhölls från skalelementmodellen. Skalmodellen, som fångar effekterna av flexibla fogar och tunga ventiler, uppvisar emellertid en spridning på de beräknade hastigheterna på upp till två storleksordningar, framför allt i lågfrekvensområdet. De parametrar som identifierades som orsaker till denna variation är förhållandet mellan ventil- och rörmassan samt fogens eftergivlighet.
Resultaten visar att såväl lutningen på klassificeringslinjerna som vidden på “Concern”-zonen i EI-diagrammet förklaras av icke-ideala egenskaper som koncentrerade massor och flexibla randvillkor. Statistiska nedre envelopper anpassade till datan visar att “Concern”- och “Problem”-kurvorna motsvarar ungefär 20- respektive 1-percentilen, vilket täcker cirka åttio respektive nittionio procent av realistiska geometrier.
Studien stödjer EI riktlinjernas giltighet och föreslår att dess tillämpningsområde kan utvidgas med skalningsfaktorer för svetskvalitet, tvärsnittsgeometri samt mycket högcykliga utmattningsfall.
Place, publisher, year, edition, pages
2025.
Series
TRITA-SCI-GRU ; 2025:121
Keywords [en]
Vibration-induced fatigue, industrial piping, Energy Institute guidelines, weld fatigue, hot-spot stress, FEA, modal analysis
Keywords [sv]
Vibrationsinducerad utmattning, industrirörsystem, Energy Institutes riktlinjer, svetsutmattning, hot-spot-spänning, modalanalys
National Category
Engineering and Technology
Identifiers
URN: urn:nbn:se:kth:diva-365663OAI: oai:DiVA.org:kth-365663DiVA, id: diva2:1977108
External cooperation
DEKRA Consulting AB
Supervisors
Examiners
2025-08-182025-06-252025-08-18Bibliographically approved