Skärdataoptimering för planfräsning i austenitisktrostfritt stål med och utan minimalsmörjning
2024 (Swedish)Independent thesis Basic level (university diploma), 10 credits / 15 HE credits
Student thesis
Abstract [sv]
Detta arbete har utförts i syfte att optimera skärdata för planfräsning av austenitiskt rostfritt stål under både torra förhållanden och med minimalsmörjning. Planfräsning är en vanlig bearbetningsmetod inom tillverkningsindustrin, och användningen av skärvätska är betydande för att minska verktygslitage och förbättra kvaliteten. Dessvärre medför konventionella skärvätskor stora investeringskostnader samt miljö och hälsorisker, vilket gör minimalsmörjning till ett intressant alternativ.
Studien har syftat till att optimera skärdataparametrar för att möjliggöra ett höjt verktygsutnyttjande inom tillverkningsindustrin och därmed minska negativa miljöeffekter och hälsopåverkan. Målet med studien var att optimera skärdata för planfräsning av austenitiskt rostfritt stål, med och utan minimalsmörjning.
Statistiska modellen skapades genom fullfaktorförsök, där fullfaktorförsöken bestod av tre nivåer för de två oberoende variablerna skärhastighet och matning, för både torra och minimalsmörjningsförhållanden. Responsvariabeln för försöken var avverkad volym vid ett visst verktygsslitage. Fulfaktorförsöken utfördes två gånger och kontrollerades med tre kontrolltester för varje beatbetningsmiljö.
Resultaten av statiska modellen visade en stor negativ effekt från minimalsmörjning på verktygslivslängden. Vid planfräsning i rostfritt stål är det viktigt att inte kyla verktyget mellan ingreppen för att inte öka den termiska utmattningen. Icke roterande verktyg kan vara lämpligare för att det testade minimalsmörjningssystemet.
Den statistiska modellen för optimering skärdata vid planfräsning av austenitiskt rostfritt stål kan användas för att maximera avverkningshastigheten när ett specifikt antal detaljer ska produceras.
Abstract [en]
The aim of this study is to optimize cutting parameter for face milling austenitic stainless steel for a dry machining environment and with the aid of a minimum quantity lubrication system. Face milling is one of the most common machining methods in the metal cutting industry. The use of cutting fluids is an important aspect for many types of machining operations. Mineral oil based emulsion is widely used as cutting fluid to improve tool life and improve part surface quality. The conventional mineral based cutting fluids require costly investments and have high maintenance costs. In addition to the high costs, the use mineral based cutting fluids have a large impact on the environment and the health concerns of personnel exposed to this fluid. This is why minimum quantity lubrication is being investigated as a reasonable alternative to conventional cutting fluids.
This study aims to optimize cutting parameters to possibly improve the usable tool life, and by these means, help reduce the costs and environmental impact of metal machining. The objective for this study was to optimize cutting parameter for face milling austenitic stainless steel, for dry machining and for machining with minimum quantity lubrication.
A surface response model was created, with two independent continuous factors, namely cutting speed and federate. The machining environment variable was implemented in design as a categorical factor. The response variable for the response surface was machined material volume at a certain measured tool wear. These tests where replicated once for all levels of continuous factors and both levels of the categorical factors. To verify the result three control test were performed for each of the machining environments.
The results of surface response model show a large negative effect on tool life with the use of minimum quantity lubrication. It is possible that this system cools the cutting tool at every revolution and is thereby thermally chocking the tool, reducing its usable life. It is when face milling important not to introduce unnecessary cooling of the cutting tool to reduce thermal fatigue.
The surface response model presented in this study can be utilized to optimize the metal removal rate for a specified required tool life or vice versa.
Place, publisher, year, edition, pages
2024. , p. 30
Keywords [en]
Face milling, Stainless steel, Surface response, 1.4301, AISI304, optimization, minimum quantity lubrication, MQL
Keywords [sv]
Planfräsning, rostfritt stål, faktorförsök, 1.4301, AISI304, optimering, minimalsmörjning, MQL
National Category
Mechanical Engineering
Identifiers
URN: urn:nbn:se:hig:diva-45424OAI: oai:DiVA.org:hig-45424DiVA, id: diva2:1895749
Subject / course
Mechanical engineering
Supervisors
Examiners
2024-09-102024-09-062025-10-02Bibliographically approved