Analysis and Improvement of Agitator for Drum Filter
2024 (English)Independent thesis Advanced level (professional degree), 20 credits / 30 HE credits
Student thesis
Abstract [en]
This project was executed to address the issue LKAB in Svappavaara is facing with failing agitators for the drum filters. The goal was to determine if the stress in the agitator during normal use was high enough to induce fatigue and to propose solutions to mitigate this problem. The project was limited to modifying only the agitator itself, without altering any other parts of the drum filter system.
The loads on the agitator were calculated using approximated formulas for similar structures. The stress analysis was performed using the finite element method (FEM). The stress was measured in the critical area where failures have occurred. The conceptual solutions were developed using Ulrich & Eppinger's product development methods.
The maximum load magnitude on the agitator was determined to be 4814 N. The resulting stress in that area during the maximum amplitude load was found to be 30 MPa, which is where the largest stress concentrations occur. This stress level is too low to cause fatigue. Even if the engine were to apply its maximum torque, resulting in stresses of 140 MPa, it would still be insufficient to cause fatigue.
Three different solutions were proposed. One reinforcement method that can reduce the stresses by 15%. Additionally, two material alternatives with greater fatigue resistance were suggested. One alternative is to switch to Hardox steel, which has proven effective in LKAB's refinement plant in Malmberget. The other is to normalize the steel currently in use.
In conclusion, the stress analysis indicates that the current stress levels are insufficient to cause fatigue under normal operating conditions. However, the proposed reinforcement and material changes can further enhance the agitator's durability and operational reliability.
Abstract [sv]
Detta projekt genomfördes för att adressera haverier av omrörare till trumfilter som LKAB i Svappavaara står inför. Målet var att fastställa om spänningarna i omröraren under normal användning var tillräckligt höga för att orsaka utmattning och att föreslå lösningar för att mildra detta problem. Projektet begränsades till att endast modifiera själva omröraren, utan att ändra några andra delar av trumfiltersystemet.
Belastningarna på omröraren beräknades med hjälp av approximativa formler för liknande strukturer. Spänningsanalysen utfördes med finita elementmetoden (FEM). Spänningen mättes i det kritiska området där haverier har observerats. De konceptuella lösningarna utvecklades med hjälp av Ulrich & Eppingers produktutvecklingsmetoder.
Den maximala belastningen på omröraren fastställdes till 4814 N. Den resulterande spänningen i det området under maximal amplitudbelastning var 30 MPa. Det är också där de största spänningskoncentrationerna uppstår. Denna spänningsnivå är för låg för att orsaka utmattning. Även om motorn skulle vrida med sitt maximala vridmoment, vilket resulterar i spänningar på 140 MPa, skulle det fortfarande vara otillräckligt för att orsaka utmattning.
Tre olika lösningar föreslogs. En förstärkningsmetod kan reducera spänningarna med 15%. Därutöver föreslogs två materialalternativ med större utmattningsbeständighet. Ett alternativ är att byta till Hardox-stål, vilket har visat sig vara effektivt i LKAB:sförädlingsanläggning i Malmberget. Det andra är att normalisera det stål som används idag.
Sammanfattningsvis indikerar spänningsanalysen att de nuvarande spänningsnivåerna är otillräckliga för att orsaka utmattning under normala driftsförhållanden. De föreslagna förstärkningarna och materialändringarna kan dock ytterligare förbättra omrörarens hållbarhet och driftssäkerhet.
Place, publisher, year, edition, pages
2024. , p. 62
Keywords [en]
Agitator, Drum, Filter, Slurry
National Category
Other Mechanical Engineering
Identifiers
URN: urn:nbn:se:ltu:diva-108337OAI: oai:DiVA.org:ltu-108337DiVA, id: diva2:1884019
External cooperation
Eurocon Engineering AB; LKAB
Educational program
Mechanical Engineering, master's level
Supervisors
Examiners
2024-08-122024-07-122025-10-21Bibliographically approved