Open this publication in new window or tab >>2026 (English)Doctoral thesis, comprehensive summary (Other academic)
Abstract [en]
In stability assessments, concrete buttress dams are typically assumed to act as intact structures, with monoliths considered in isolation. This neglects the impact of effects such as preexisting cracks and interaction between monoliths. Neglecting these mechanisms can lead to either over- or underestimation of the load-bearing capacity and may also affect the predicted failure behavior. The aim of this thesis is therefore to improve the understanding and assessment of the stability and failure behavior of concrete buttress dams, with particular focus on monolith interaction, structural cracks, and the requirements of numerical modeling.
These phenomena were assessed with a combination of physical and numerical models. The physical model tests were performed to establish the failure behavior of isolated and interacting buttress dams with both cracked and intact monoliths. Finite element (FE) simulations were used to reproduce the physical tests, validate the numerical approaches, and extend the analyses beyond the experimentally tested configurations. The numerical models ranged from relatively simple predefined frictional interfaces to distributed concrete cracking and a reinforced rough-crack model incorporating aggregate interlock and reinforcement action.
Monolith interaction was shown to significantly alter both the load-bearing capacity and failure behavior of buttress dams, with the largest increases in resistance observed for short dams with steep cross-valley foundation inclinations. Failure of individual monoliths was found to be unlikely while interaction and contact with adjacent monoliths were maintained. However, considerable displacement may be required to mobilize this interaction. The associated increase in resistance should therefore generally not be credited in the primary stability assessment, but rather be regarded as reserve capacity that may be important for predicting the global failure behavior of the dam.
Structural cracks have been shown to affect both the load-bearing capacity and failure mode of buttress dams. A cracked buttress dam can first be represented as blocks separated by smooth planes with Coulomb-friction interfaces, with aggregate interlock and reinforcement crossing the crack omitted. If this simplified representation demonstrates stability, it is sufficient for assessing the load-bearing capacity. However, these models may misrepresent failure modes and are less suitable for predicting the actual behavior of the dam. If the simplified block model does not demonstrate adequate stability, the effects of aggregate interlock and reinforcement crossing the crack may need to be included. For reinforced rough cracks, the initial crack width was found to strongly influence the load-bearing capacity and, in some cases, the governing failure mode. Therefore, a model that includes reinforcement but represents the crack interface using Coulomb friction cannot generally be assumed to provide a conservative estimate of the load-bearing capacity.
The required numerical model complexity was found to depend on the behavior of interest and the objective of the analysis. Simplified models were adequate for failures dominated by rigid-body motion, whereas three-dimensional interaction, material failure, and reinforced crack behavior required more detailed representations. These findings also have implications for dam monitoring, where stability assessments can help identify relevant local and global response quantities and structurally important cracks. However, the monitoring implications remain qualitative, and further validation under representative field conditions is required to reduce uncertainties associated with real foundation interfaces and aged structural cracks.
Abstract [sv]
Vid stabilitetsanalyser av lamelldammar antas dammen vanligtvis vara intakt och monoliterna betraktas var för sig. Därmed försummas effekten av genomgående sprickor och interaktion mellan monoliter. Att bortse från dessa mekanismer kan leda till både över- och underskattning av bärförmågan och även påverka den förväntade brottmoden. Syftet med denna avhandling är därför att förbättra förståelsen för och bedömningen av stabilitet och brottbeteende hos lamelldammar, med särskilt fokus på interaktion mellan monoliter, genomgående sprickor och krav vid numerisk modellering.
Dessa fenomen studerades med en kombination av fysiska och numeriska modeller. De fysiska modellförsöken genomfördes för att undersöka brottbeteendet hos monoliter med respektive utan interaktion, samt med och utan genomgående sprickor. Finita elementanalyser (FE-analyser) användes för att reproducera modellförsöken, validera de numeriska modelleringsmetoderna och utvidga analyserna till konfigurationer som inte studerats experimentellt. De numeriska modellerna sträckte sig från relativt enkla modeller med fördefinierade friktionsytor till modeller med sprickbildning i betongen och en modell för armerade sprickor med råa sprickytor, där ballastinteraktion och armeringens bidrag beaktades.
Interaktion mellan monoliter visades kunna påverka både bärförmågan och brottbeteendet hos lamelldammar avsevärt. De största ökningarna i bärförmåga skedde i korta dammar med brant lutande grundläggningsytor i tvärled. Brott i enskilda monoliter bedömdes som osannolika så länge kontakt och interaktion med angränsande monoliter upprätthölls. Betydande deformation kan dock krävas för att mobilisera denna interaktion. Den ökade bärförmågan bör därför i regel inte tillgodoräknas i den primära stabilitetsanalysen, utan snarare betraktas som reservkapacitet. Interaktion är också viktig för att förutsäga dammens globala brottbeteende.
Genomgående sprickor visades kunna påverka både bärförmågan och brottmoden hos lamelldammar. Om en sprucken lamelldamm kan visas vara stabil när den representeras som separata block åtskilda av släta ytor med Coulomb-friktion, där både ballastinteraktion och armering som korsar sprickan försummas, är sådana förenklade modeller tillräckliga för bedömning av bärförmågan. Modellerna kan dock ge felaktiga brottmoder och är mindre lämpliga för att förutsäga dammens faktiska beteende. Om den förenklade blockmodellen inte visar tillräcklig stabilitet kan ballastinteraktion och armering som korsar sprickan behöva inkluderas. För armerade sprickor med råa sprickytor visades den initiala sprickvidden ha stor inverkan på bärförmågan och i vissa fall även på den styrande brottmoden. En modell där armeringen beaktas men sprickytan representeras med Coulomb-friktion kan därför inte generellt antas ge en konservativ uppskattning av bärförmågan.
Hur detaljerad den numeriska modellen behöver vara beror på vilket beteende som ska studeras och på syftet med analysen. Förenklade modeller var tillräckliga för brott som huvudsakligen styrdes av stelkroppsrörelser, medan tredimensionell interaktion, materialbrott och beteendet hos armerade sprickor krävde mer detaljerade modeller. Resultaten har även betydelse för övervakning av dammar, där stabilitetsanalyser kan användas för att identifiera relevanta lokala och globala responsparametrar samt strukturellt viktiga sprickor. Slutsatserna avseende övervakning är dock kvalitativa och ytterligare validering under representativa fältförhållanden krävs för att minska osäkerheterna kopplade till verkliga grundläggningsytor och genomgående sprickor påverkade av nedbrytning.
Place, publisher, year, edition, pages
Stockholm: KTH Royal Institute of Technology, 2026. p. 81
Series
TRITA-ABE-DLT ; 2640
National Category
Infrastructure Engineering
Research subject
Civil and Architectural Engineering, Concrete Structures
Identifiers
urn:nbn:se:kth:diva-392117 (URN)978-91-8106-773-6 (ISBN)
Public defence
2026-12-09, Kollegiesalen, Brinellvägen 8, KTH Campus, public video conference link https://kth-se.zoom.us/j/62987411517, Stockholm, 10:00 (English)
Opponent
Supervisors
Note
QC 20261106
2026-11-062026-11-062026-11-06Bibliographically approved