Change search
ReferencesLink to record
Permanent link

Direct link
Hot forming tribology: galling of tools and associated problems
Luleå University of Technology, Department of Engineering Sciences and Mathematics, Machine Elements.
2011 (English)Licentiate thesis, comprehensive summary (Other academic)
Abstract [en]

In recent years, the use of ultra high-strength steels (UHSS) as structural reinforcements and in energy-absorbing systems in automobiles has increased rapidly; mainly in view of their favourable strength to weight ratios. However, due to their high strength, the formability of UHSS is poor, thus complex-shaped UHSS components are invariably produced through hot-metal forming processes. The use of hot stamping or press hardening, which was developed during the 1970’s in northern Sweden, has become increasingly popular for the production of ultra high strength steels. In hot stamping, different tribological problems arise when the tool and work-piece interact during the forming process at elevated temperatures. Wear and surface damage of forming tools can be detrimental to the quality of the final product and these can also have an adverse impact on the process economy due to frequent maintenance or replacement of tools. In this work, a literature review pertaining to tribology of hot sheet metal forming has been carried out. This review has revealed that the awareness of tribology and its application in metal forming processes at high temperature has increased in the recent years. A considerable amount of work has been done to enhance the understanding of the response of different materials and parameters involved and also to improve the process itself. However, despite these developments, there exist major gaps in knowledge pertaining to the occurrence of friction and wear in hot sheet metal forming. Extensive experimental studies have thus been undertaken to bridge some of the knowledge gaps related to tool wear and failure mechanisms in the hot stamping process. These studies have involved both the systematic analysis of actual worn tools as well as parametric tribological investigations in the laboratory. The analysis of worn tools showed that friction is a crucial parameter in their operating life. It was observed that severe mechanical stresses are generated due to high friction during the work-piece/tool interaction. As a result of the cyclic thermal and mechanical loads imposed during the hot forming process, the stresses generated eventually lead to the occurrence of fatigue damage at the tool surface. Another important mechanism observed was material transfer from the work-piece to the tool surface. This is particularly common and detrimental in hot forming of coated work-piece material. The most common coating applied to the ultra high strength steel is a hot dip aluminium based coating, commonly referred to as Al-Si coating. The parametric studies carried out were aimed at understanding of the initiation mechanisms of material transfer from the Al-Si coated steel to the tool material. The results showed that severe galling occurs by accumulation and compaction of wear debris and becomes enhanced in tools having rough surfaces. The roughness defects on the surface promote accumulation of wear particles. Furthermore, high contact pressure also enhances the compaction of wear debris and consequently the severity of material transfer. It was observed that the severity of galling can be reduced by the use of smooth and hard surfaces. Additionally, the use of different PVD coatings on the tool steels showed an increased tendency on adhesion, causing a severe material transfer onto the tool surface.

Place, publisher, year, edition, pages
Luleå: Luleå tekniska universitet, 2011. , 82 p.
Licentiate thesis / Luleå University of Technology, ISSN 1402-1757
Research subject
Machine Elements
URN: urn:nbn:se:ltu:diva-25915Local ID: bb160a14-1656-4039-a5f1-31c5359f525eISBN: 978-91-7439-308-8OAI: diva2:999073
Godkänd; 2011; 20110902 (leopel); LICENTIATSEMINARIUM Ämnesområde: Maskinelement/Machine Elements Examinator: Professor Braham Prakash, Institutionen för teknikvetenskap och matematik, Luleå tekniska universitet Diskutant: Dipl.-Ing. Dr.mont.(PhD) Ewald Badisch, AC2T Research GmbH, Wiener Neustadt, Austria Tid: Torsdag den 6 oktober 2011 kl 10.00 Plats: E231, Luleå tekniska universitetAvailable from: 2016-09-30 Created: 2016-09-30Bibliographically approved

Open Access in DiVA

fulltext(11413 kB)0 downloads
File information
File name FULLTEXT01.pdfFile size 11413 kBChecksum SHA-512
Type fulltextMimetype application/pdf

Search in DiVA

By author/editor
Pelcastre, Leonardo
By organisation
Machine Elements

Search outside of DiVA

GoogleGoogle Scholar
The number of downloads is the sum of all downloads of full texts. It may include eg previous versions that are now no longer available

ReferencesLink to record
Permanent link

Direct link