Change search
ReferencesLink to record
Permanent link

Direct link
Prediction of hardening, localization and fracture of multiphase microstructure in boron alloyed steel
Luleå University of Technology, Department of Engineering Sciences and Mathematics, Mechanics of Solid Materials.
2014 (English)Licentiate thesis, comprehensive summary (Other academic)
Abstract [en]

Over recent years the demand of press hardened ultra-high strength steel for safety structures in automobiles has increased and continuation of this trend is expected.Components with tailored material properties can be manufactured using a thermo-mechanical process with heated and cooled areas in a tool. In industry the cooling rate of the blank is controlled this utilizes the formation of different microstructures with varying mechanical properties within a single component.The structural response in a crash situation can be altered by the design of the component with formation of different material grades based on the microstructure in designated areas of the component.Material models used in finite element analysis are required by the automotive industry and its suppliers. These models contribute to the improvement and quality of press hardened components.In this work a set of tensile test specimens with different volume fractions of phases are produced. As material is the boron steel 22MnB5 chosen which is a common material used in press hardening due to its good hardenability. The specimens are austenitized before starting the heat treatment at different temperatures and holding times. In total fourteen different microstructures are produced. Reference material grades for pure phases are ferrite, bainite and martensite. The produced samples consist of ferrite-bainite, ferrite-martensite and bainite-martensite with different volume fractions, additionally a microstructure consisting of three phases, ferrite-bainite and martensite, is available. Using measured mechanical properties of pure phases and the volume fraction of formed phases different homogenization methods are compared in their ability to represent the mechanical response of mixed microstructures. The homogenization methods account for elastic deformation and the hardening of the material. The onset of necking is seen as the last valid point for all homogenization methods. After this point a localization and damage function for the prediction of softening and fracture is applied. Strain localization and fracture are mesh dependent, therefore an analysis length scale is introduced to account for different element sizes. A weakest link criterion is used for fracture. This means failure of the composite is assumed to occur if one phase fails. The material model for homogenization of mixed microstructures including damage is implemented in the commercial available finite element code LS-Dyna and validated by comparison to experimental results.

Place, publisher, year, edition, pages
Luleå tekniska universitet, 2014.
Series
Licentiate thesis / Luleå University of Technology, ISSN 1402-1757
Research subject
Solid Mechanics
Identifiers
URN: urn:nbn:se:ltu:diva-18551Local ID: 921727fc-b399-4715-82d4-49fa3bb1f396ISBN: 978-91-7583-133-6ISBN: 978-91-7583-134-3 (PDF)OAI: oai:DiVA.org:ltu-18551DiVA: diva2:991560
Note
Godkänd; 2014; 20141003 (stegol); Nedanstående person kommer att hålla licentiatseminarium för avläggande av teknologie licentiatexamen. Namn: Stefan Golling Ämne: Hållfasthetslära/Solid Mechanics Uppsats: Prediction of Hardening, Localization and Fracture of Multiphase Microstructure in Boron Alloyed Steel Examinator: Professor Mats Oldenburg Institutionen för teknikvetenskap och matematik Avdelning Material- och solidmekanik Diskutant: Doktor Daniel Berglund Gestamp HardTech, Lule Tid: Onsdag den 17 december 2014 kl 10.00 Plats: E246, Luleå tekniska universitetAvailable from: 2016-09-29 Created: 2016-09-29Bibliographically approved

Open Access in DiVA

fulltext(8332 kB)10 downloads
File information
File name FULLTEXT01.pdfFile size 8332 kBChecksum SHA-512
e00cfcfb870846d8ba9c056901d60a66c99c7f95b06a82bc68d15d604f24c7c533a0f3f1194531c85615801e588631dd791deaf76eb53475fbce7d0b643bcc24
Type fulltextMimetype application/pdf

Search in DiVA

By author/editor
Golling, Stefan
By organisation
Mechanics of Solid Materials

Search outside of DiVA

GoogleGoogle Scholar
Total: 10 downloads
The number of downloads is the sum of all downloads of full texts. It may include eg previous versions that are now no longer available

Total: 17 hits
ReferencesLink to record
Permanent link

Direct link