Change search
ReferencesLink to record
Permanent link

Direct link
Rough surface elastohydrodynamic lubrication and contact mechanics
Luleå University of Technology, Department of Engineering Sciences and Mathematics, Machine Elements.
2004 (English)Licentiate thesis, comprehensive summary (Other academic)
Abstract [en]

In the field of tribology, there are numerous theoretical models that may be described mathematically in the form of integro-differential systems of equations. Some of these systems of equations are sufficiently well posed to allow for numerical solutions to be carried out resulting in accurate predictions. This work has focused on the contact between rough surfaces with or without a separating lubricant film. The objective was to investigate how surface topography influences contact conditions. For this purpose two different numerical methods were developed and used. For the lubricated contact between rough surfaces the Reynolds equation were used as a basis. This equation is derived under the assumptions of thin fluid film and creeping flow. In highly loaded, lubricated, non- conformal contacts of surfaces after running-in, the load concentration no longer results in plastic deformations, however large elastic deformations will be apparent. It is the interaction between the hydrodynamic action of the lubricant and the elastic deformations of the surfaces that, in certain applications, enable the lubricant film to fully separate the surfaces. This is commonly referred to as full film elastohydrodynamic (EHD) lubrication. Typical machine elements that operates in the full film EHD lubrication (FL) regime include rolling element bearings, cams and gears. Unfortunately, a cost effective way of machining engineering surfaces seldom results in a surface topography that influence contact conditions in the same way as a surface after running-in. Such topographies may prevent the lubricant from fully separating the surfaces because of deteriorated hydrodynamic action. In this case the applied load is carried in part by the lubricant and in part by surface asperities and/or surface active lubricant additives. This could also be the case in lubricant starved contacts, which is a common situation in not only grease lubricated contacts but also in many liquid lubricated contacts, such as high speed operating rolling element bearings. The load sharing between the highly compressed lubricant and the surface and/or surface active lubricant additives is the reason why this lubrication regime is most commonly referred to as mixed EHD lubrication (ML). Machine elements that while running operate in the FL regime may experience a transition into the ML regime at stops or due to altered operating conditions. It is not possible to simulate direct contact between the surfaces using a numerical method based on Reynolds equation. A parameter study, of elementary surface features passing each other inside the EHD lubricated conjunction, was performed. The results obtained, even though no direct contact could be simulated, does indicate that a transition from the FL to the ML regime would occur for certain combinations of the varied parameters. At start-ups, the contact in a rolling element bearing could be both starved and drained from lubricant. In this case the hydrodynamic action becomes negligible in terms of load carrying capacity. The load is carried exclusively by surface asperities and/or surface active lubricant additives. This regime is referred to as boundary lubrication (BL). Operation conditions could also make both FL and ML impossible to achieve, for example, in the case in a low rpm operating rolling element bearing. The BL regime is in this work modeled as the unlubricated frictionless contact between rough surfaces, i.e., a dry contact approach. A variational principle was used in which the real area of contact and contact pressure distribution are those which minimize the total complementary energy. A linear elastic-perfectly plastic deformation model in which energy dissipation due to plastic deformation is accounted for was used. The dry contact method was applied to the contact between four different profiles and a plane. The variation in the real area of contact, the plasticity index and some surface roughness parameters due to applied load were investigated. The surface roughness parameters of the profiles differed significantly.

Place, publisher, year, edition, pages
Luleå: Luleå tekniska universitet, 2004. , 116 p.
Licentiate thesis / Luleå University of Technology, ISSN 1402-1757 ; 2004:35
Research subject
Machine Elements
URN: urn:nbn:se:ltu:diva-18385Local ID: 860465d0-aef4-11db-803d-000ea68e967bOAI: diva2:991393
Godkänd; 2004; 20070128 (ysko)Available from: 2016-09-29 Created: 2016-09-29Bibliographically approved

Open Access in DiVA

fulltext(4921 kB)32 downloads
File information
File name FULLTEXT01.pdfFile size 4921 kBChecksum SHA-512
Type fulltextMimetype application/pdf

Search in DiVA

By author/editor
Almqvist, Andreas
By organisation
Machine Elements

Search outside of DiVA

GoogleGoogle Scholar
Total: 32 downloads
The number of downloads is the sum of all downloads of full texts. It may include eg previous versions that are now no longer available

Total: 36 hits
ReferencesLink to record
Permanent link

Direct link