Change search
ReferencesLink to record
Permanent link

Direct link
Vippning av stålbalkar i hallramar
Luleå University of Technology, Department of Civil, Environmental and Natural Resources Engineering, Structural and Construction Engineering.
1991 (Swedish)Doctoral thesis, comprehensive summary (Other academic)
Abstract [en]

The present thesis, written in Swedish, deals with the problem of lateral-torsional buckling, especially in gable frames. The aim of the work presented is to suggest an improved design method that takes into account the translational and rotational restraint produced by the roof and wall. A particular question is the behaviour of the comer region. More specific, is it a safe assumption to consider the comer as a lateral support. The study includes a review of literature and design methods, analytical solutions of some stability problems, tests on four frames and a FEM simulation. The design methods for lateral buckling usually start from the elastic critical load which defines a relative slenderness of the structure. This slenderness finally gives the predicted capacity. The lateral buckling theory has to take cross-sectional distortion into account because the rotational restraint is often provided concentratedly by purlins or wall rails. This distortion is important also for rolled beams which was not expected. Closed form solutions are presented for the column and references are given to solutions for the roof beam. In order to get some indication of the stability of the comer of a frame, the inner flanges and the stiffener were modelled as a three rod system. The slope of the roof turned out to be of no significance. The results also indicated that the stability of the comer could be questioned when the critical loads of the column and the girder were close to each other. This conclusion was also reached by studies of elasto-plastic frames carried out by Stoverink, at the RWIH, Aachen. Four frames of IPE 180, of which two were haunched, were tested. The two unhaunched frames reached their plastic capacity, and showed a ductile behaviour although their relative slenderness was above the normally accepted limit for full capacity. The two haunched frames, however, buckled before their plastic capacity was reached. This indicates that haunched frames of this type can not be expected to develop their full plastic capacity under conditions similar to those during testing. Finally, the Swedish standards are compared with experimental results, and improvements are suggested. Guidelines are also drawn up for the design of low-rise frames with respect to lateral buckling.

Abstract [sv]

Denna rapport behandlar vippning av dubbelsymmetriska balkar, med tonvikt på balkelement i tvåledsramar. I kapitel 1 ges en kort inledning till problemställningen och teorin kring vippning, Dessutom belyses fördelen av dimensionering av hallramar med gränslastmetod.Kapitel 2 behandlar dels historik men även några större undersökningar, ur vilka intressant information kan hämtas.I kapitel 3.1 studeras interaktionen mellan styrd vippning och böjvridknäckning för ett pelarben utsatt för konstant normalkraft och triangulärt fördelat moment. Dessutom presenteras en approximativ formel för kritiskt moment.Kapitel 3.2 behandlar bunden vippning av initiellt rak balk under närvaro av egenspänningar. Inverkan studeras av styrningsaxeln, egenspänningarnas storlek samt en reducerad skjuvmodul i genomflutna delar av tvärsnittet.För att få en fingervisning om stabiliteten av de tryckta innerflänsarna i ett ramhörn studeras i kapitel 3.3 en stångmodell bestående av innerflänsarna och hörnets diagonalavstyvning. Modellen tyder på diskutabel stabilitet hos hörnet då takbalken och pelarbenet har samma kritiska laster.Inverkan av vridinspänning av balkar samt livdeformationer diskuteras i kapitel 3.4 och 3.5.I kapitel 4 presenteras resultatet av beräkningar gjorda med FEM-programmet ABAQUS. Inverkan av vridinspänning, stagning och initialkrokighet hos ett ramhörn studeras.I kapitel 5 beskrivs försök utförda på fyra ramhörn, två votade och två ovotade. De två ovotade ramarna uppnådde plastiskt moment, och uppvisade plastisk rotation. De votade ramarna uppvisade brott vid votens slut, och även ett sprött beteende.I kapitel 6 diskuteras resultaten från föregående kapitel. Dessutom görs jämförelser mellan olika normer och försöksresultat. Avslutningsvis dras riktlinjer upp för kontroll av stabilitet hos hallramar. För resultat och slutsatser hänvisas till detta kapitel.

Place, publisher, year, edition, pages
Luleå: Luleå tekniska universitet, 1991. , 120 p.
Series
Doctoral thesis / Luleå University of Technologyy… → 31 dec 1996, ISSN 0348-8373 ; 94
Research subject
Steel Structures; Structural Engineering
Identifiers
URN: urn:nbn:se:ltu:diva-17843Local ID: 57e66130-f418-11db-ac9f-000ea68e967bOAI: oai:DiVA.org:ltu-17843DiVA: diva2:990849
Note
Godkänd; 1991; 20070426 (ysko)Available from: 2016-09-29 Created: 2016-09-29Bibliographically approved

Open Access in DiVA

fulltext(18486 kB)1 downloads
File information
File name FULLTEXT01.pdfFile size 18486 kBChecksum SHA-512
d4b82f09f63bad4393ab15f4008e13c57e235e03a7fbf8114da89c7c5c377bb7f86e898827c63108dfb7b71c5be9a4a695dd397b48c4aca28388e624ac43b627
Type fulltextMimetype application/pdf

Search in DiVA

By author/editor
Collin, Peter
By organisation
Structural and Construction Engineering

Search outside of DiVA

GoogleGoogle Scholar
Total: 1 downloads
The number of downloads is the sum of all downloads of full texts. It may include eg previous versions that are now no longer available

Total: 21 hits
ReferencesLink to record
Permanent link

Direct link