Change search
ReferencesLink to record
Permanent link

Direct link
Experiments on sheet metal shearing
Luleå University of Technology, Department of Engineering Sciences and Mathematics, Mechanics of Solid Materials.
2013 (English)Licentiate thesis, comprehensive summary (Other academic)
Abstract [en]

Within the sheet metal industry, different shear cutting technologies are commonly used in several processing steps, e.g. in cut to length lines, slitting lines, end cropping etc. Shearing has speed and cost advantages over competing cutting methods like laser and plasma cutting, but involves large forces on the equipment and large strains in the sheet material.Numerical models to predict forces and sheared edge geometry for different sheet metal grades and different shear parameter set-ups are desirable. For new sheet metal grades, numerical shear models are efficient for finding appropriate shear parameters without the need for time consuming and expensive live tests in the production. In order to allow for validation of numerical models, accurate experimental data is wanted.Many industrial equipments for shearing give some measure of applied force, but due to machinery friction losses, measured forces are always higher than the forces acting on the sheet. Shearing also generates a force that attempts to separate the two shear tools with changed shear conditions through increased clearance between the shear tools as result. Clearance is also the most common shear parameter to adjust, depending on material grade and sheet thickness, in order to moderate the required force and to control the final sheared edge geometry.Sheared edges have four characteristic zones, rollover, shear, fracture and burr zones. Burrs and rough fracture zones complicate the following processing through inadequate tolerances that may imply additional machining and sharp edges that may damage equipment or even cause injuries. Well defined shears and accurate measurements are important for the understanding of shear parameters. In this work, an experimental procedure with high measurability and consistent and predictable output, is designed, built and evaluated. Important shear parameters and demands on the experimental set-up are identified in a perturbation analysis performed with use of finite element method.Considering the perturbation analyses results, experimental set-up requirements are formulated. Based on magnitude of the force changes obtained as result of perturbed input parameters in the analyses, force measurements with one percent accuracy are considered necessary. Since a clearance change of one percentage point results in approximately one percent change in forces, the target experimental clearance stability is an order of magnitude lower, i.e. the clearance should remain within 0.1% or 5μm at the sheet thicknesses sheared.With respect to high clearance stability and accurate force measurements, a symmetric experiment with two simultaneous shears and internal balancing of forces attempting to separate the shear tools, is constructed. Besides a stable clearance, the experiment features high accuracy force measurements without external friction losses through 20 strain gauges mounted on the set-up.Since clearance and clamping of the sheet are identified as important to the shear results, these parameters are selected for further experimental studies through shearing of three material grades with various strength. Judging by the result, shear tool penetration before fracture decreases with increased material strength. When one side of the sheet is left unclamped and free to move, the required shear force decreases but instead the force attempting to separate the two shear tools increase. Further, the maximum shear force increases and the rollover decreases with decreased clearance. In general terms, results from the study are promising for use in validation of numerical shear models.

Place, publisher, year, edition, pages
Luleå: Luleå tekniska universitet, 2013.
Series
Licentiate thesis / Luleå University of Technology, ISSN 1402-1757
Research subject
Solid Mechanics
Identifiers
URN: urn:nbn:se:ltu:diva-17805Local ID: 54d1c713-062d-485b-968a-323ff512dc1eISBN: 978-91-7439-622-5ISBN: 978-91-7439-623-2 (PDF)OAI: oai:DiVA.org:ltu-17805DiVA: diva2:990811
Note
Godkänd; 2013; 20130430 (emigus); Tillkännagivande licentiatseminarium 2013-05-16 Nedanstående person kommer att hålla licentiatseminarium för avläggande av teknologie licentiatexamen. Namn: Emil Gustafsson Ämne: Hållfasthetslära/Solid Mechanics Uppsats: Experiments on Sheet Metal Shearing Examinator: Professor Mats Oldenburg, Institutionen för teknikvetenskap och matematik, Luleå tekniska universitet Diskutant: Doktor Magnus Eriksson, SINTEF Materials and Chemistry, Structural Mechanics, Trondheim, Norge Tid: Torsdag den 30 maj 2013 kl 10.00 Plats: E246, Luleå tekniska universitetAvailable from: 2016-09-29 Created: 2016-09-29Bibliographically approved

Open Access in DiVA

fulltext(4537 kB)7 downloads
File information
File name FULLTEXT01.pdfFile size 4537 kBChecksum SHA-512
6dea12556c9e2c3f058cff2fd72fa2bbc06802d335718f4944f796d114ce5ed8eb0d7c3d9a88a333de6305323e6bae644803edd68223ffdbaf7d4c8acd1b3930
Type fulltextMimetype application/pdf

Search in DiVA

By author/editor
Gustafsson, Emil
By organisation
Mechanics of Solid Materials

Search outside of DiVA

GoogleGoogle Scholar
Total: 7 downloads
The number of downloads is the sum of all downloads of full texts. It may include eg previous versions that are now no longer available

Total: 29 hits
ReferencesLink to record
Permanent link

Direct link