Change search
ReferencesLink to record
Permanent link

Direct link
µPIV Measurement of Grease Velocity Profiles
Luleå University of Technology, Department of Engineering Sciences and Mathematics, Machine Elements.
2013 (English)Licentiate thesis, comprehensive summary (Other academic)
Abstract [en]

Lubricating grease is commonly applied to lubricate e.g. rolling bearings, seals and gears. Grease has some clear advantages over lubricating oil. It is a semi-solid material, which prevents it from flowing/leaking out from the lubricated system and gives it sealing properties, protecting the system against contaminants. Unlike oil, grease has a much more complicated rheology, which makes it more difficult to model and understand grease flow. Grease acts as a lubricant reservoir, and understanding grease flow is essential in order to model and predict how grease is transported within e.g., a rolling element bearing housing, a sealing arrangement or replenishment of a gear mesh. Three greases with different rheological behaviors (NLGI 2 grease, NLGI1 grease and NLGI00 grease) have been used in two kinds of test rigs: a straight channel with different restrictions and a rotating shaft with two narrow gap sealing-like restrictions.In the first test rig two types of flow restrictions were applied into a straight channel in order to simulate flow of grease near a sealing pocket. In the case of a single restriction, the distance required for the velocity profile to fully develop when going from a wide to a narrow gap is approximately the same as the initial height of the channel. In the corner pocket before and after the restriction, the velocity is very low and part of the grease is stationary. For the channel with two flow restrictions, this effect is even more pronounced in the “pocket” between the restrictions. Clearly, a large part of the grease is not moving since the yield stress of the grease is not exceeded. This condition particularly applies to the cases with a low-pressure gradient and where high consistency grease is used. In practice this means that grease is not replaced in such “pockets” and that some aged/contaminated grease will remain there. A test rig comprising of a rotating shaft with two narrow gap sealing-like restrictions (a so called Double Restriction Seal, DRS) was designed to simulate the a labyrinth type of seal. Two different gap heights in the DRS have been designed to compare grease flow. It is shown that partially yielded grease is detected in the large gap geometry and fully yielded grease in the small gap geometry. Grease shear thinning behavior and wall slip effects have been detected and discussed. For the small gap geometry, it is shown that three distinct grease flow regions are present: a slip layer close to the stationary wall, a bulk flow layer, and a slip layer near the rotating shaft.

Place, publisher, year, edition, pages
Luleå: Luleå tekniska universitet, 2013.
Series
Licentiate thesis / Luleå University of Technology, ISSN 1402-1757
Research subject
Machine Elements
Identifiers
URN: urn:nbn:se:ltu:diva-17504Local ID: 3b1c8e46-9897-4ea7-9033-13051abffb9eISBN: 978-91-7439-562-4OAI: oai:DiVA.org:ltu-17504DiVA: diva2:990509
Note
Godkänd; 2013; 20130219 (jinlit); Tillkännagivande licentiatseminarium 2013-03-08 Nedanstående person kommer att hålla licentiatseminarium för avläggande av teknologie licentiatexamen. Namn: Jinxia Li Ämne: Maskinelement/Machine Elements Uppsats: µPIV Measurement of Grease Velocity Profiles Examinator: Professor Erik Höglund, Institutionen för teknikvetenskap och matematik, Luleå tekniska universitet Diskutant: Teknologie doktor Henrik Åström, SCANIA, Södertälje Tid: Måndag den 25 mars 2013 kl 10.00 Plats: E231, Luleå tekniska universitetAvailable from: 2016-09-29 Created: 2016-09-29Bibliographically approved

Open Access in DiVA

fulltext(5591 kB)8 downloads
File information
File name FULLTEXT01.pdfFile size 5591 kBChecksum SHA-512
162d8fad50fc7133891e4bfddf5d610c50ee9ca8933d79e544461da77277202d01f8f2ddab9b3cea4bd27c70fff17fd986dc40782c794844a829cf6e885a1033
Type fulltextMimetype application/pdf

Search in DiVA

By author/editor
Li, Jinxia
By organisation
Machine Elements

Search outside of DiVA

GoogleGoogle Scholar
Total: 8 downloads
The number of downloads is the sum of all downloads of full texts. It may include eg previous versions that are now no longer available

Total: 13 hits
ReferencesLink to record
Permanent link

Direct link