Change search
ReferencesLink to record
Permanent link

Direct link
On Determination of Gmax by Bender Element and Cross-Hole Testing
Norwegian University of Science and Technology, Faculty of Engineering Science and Technology, Department of Civil and Transport Engineering.
2014 (English)MasteroppgaveStudent thesis
Abstract [en]

The small-strain shear modulus, G<sub>max</sub>, is an important parameter in geodynamic problems and for advanced modelling. G<sub>max</sub> is influenced by several factors, which complicates the assessment and interpretation of test results. Due to sample disturbance, values measured in the laboratory may be lower than in the field. The use of G<sub>max</sub> as a measure of sample disturbance has previously been investigated. Different testing methods for determination of G<sub>max</sub> are described in this thesis, with a presentation of advantages and limitations on the basis of literature. Field tests can be performed either from the ground surface or in boreholes. For determination of G<sub>max</sub> in the laboratory, the use of bender elements in conventional test devices, such as the triaxial apparatus, has become a common procedure. With bender elements, several repetitive tests can be performed, and the sample can subsequently be tested for other soil characteristics. The initial part of this study concerned implementation of bender elements in a triaxial apparatus at the NTNU geotechnical laboratory. Subsequently, determination of G<sub>max</sub> by bender element testing was emphasized. Clay samples from three different sites were used, the Stjørdal, Tiller and Esp sites. At the Esp site, a limited field testing program was also performed, using a cross-hole method for determination of in situ G<sub>max</sub>. Laboratory measurements on two samples of Esp clay gave G<sub>max</sub> of 27 MPa and 30 MPa, after long-term consolidation. In situ measurements gave consistent results, with an average G<sub>max</sub> of 47 MPa. Values measured in the laboratory are seen to be about 40 % lower than values measured in the field. However, it should be noted that in the bender element test, the direction of propagation of the s-wave is vertical, while in the cross-hole test, it is horizontal. Consequently, due to anisotropy, a direct comparison may be somewhat erroneous. Factors influencing G<sub>max</sub> are presented on the basis of literature. Void ratio, plasticity index and soil structure are seen to be important factors. G<sub>max</sub> also show a stress dependency, increasing with increasing overburden pressure. Literature regarding G<sub>max</sub> as a measure of sample disturbance is also presented. For evaluation of the development of G<sub>max</sub> with time, long-term consolidation was performed. An evident increase in G<sub>max</sub> with time of consolidation was observed, with a correlation to axial strain. This is assumed to be due to aging effects, bringing the sample closer to its in situ state. Observations also showed a larger increase for 54 mm tube samples than for block samples, indicating some correlation between sample quality and G<sub>max</sub>. Reconsolidation seems to compensate for some effects of disturbance. However, it is suggested that destructuration of the soil is an important factor of sample disturbance which is not eliminated by reconsolidation. Bender element testing of the Esp clay was also performed on a sample of half height (5 cm). The results showed G<sub>max</sub> values about 25 % lower than those of the full-height samples. This indicates the existence of some near-field effects influencing the shear wave velocity close to the elements. Interpretation of cross-hole results revealed some difficulties regarding identification of the shear wave. The equipment should be further developed so that receivers are in direct contact with the soil. Lack of knowledge regarding an assumed complex environment in the triaxial cell, may have been a limitation when interpreting laboratory results. A model of the bender element test in a finite element method program, such as Plaxis, may be of interest for investigation of the actual condition of wave propagation. Further work is also proposed regarding the use of Gmax as a measure on sample disturbance.

Place, publisher, year, edition, pages
Institutt for bygg, anlegg og transport , 2014. , 243 p.
Keyword [no]
ntnudaim:10945, MTBYGG Bygg- og miljøteknikk, Geoteknikk
URN: urn:nbn:no:ntnu:diva-27232Local ID: ntnudaim:10945OAI: diva2:762905
Available from: 2014-11-13 Created: 2014-11-13

Open Access in DiVA

fulltext(9511 kB)1196 downloads
File information
File name FULLTEXT01.pdfFile size 9511 kBChecksum SHA-512
Type fulltextMimetype application/pdf
cover(185 kB)4 downloads
File information
File name COVER01.pdfFile size 185 kBChecksum SHA-512
Type coverMimetype application/pdf
attachment(643428 kB)7 downloads
File information
File name ATTACHMENT01.zipFile size 643428 kBChecksum SHA-512
Type attachmentMimetype application/zip

By organisation
Department of Civil and Transport Engineering

Search outside of DiVA

GoogleGoogle Scholar
Total: 1196 downloads
The number of downloads is the sum of all downloads of full texts. It may include eg previous versions that are now no longer available

Total: 60 hits
ReferencesLink to record
Permanent link

Direct link