Change search
ReferencesLink to record
Permanent link

Direct link
Ammunition for measurements
Linköping University, Department of Science and Technology. Linköping University, The Institute of Technology.
2005 (English)Independent thesis Advanced level (degree of Master (Two Years)), 20 credits / 30 HE creditsStudent thesisAlternative title
Mätskott 3P (Swedish)
Abstract [en]

The proximity fuzed 3P ammunition is programmed during the loading of the piece to the desired operation mode. To guarantee that the ammunition receives the programming signals correctly and thus being able to eliminate the programming as a source of errors in the event of a possible failure there is a need to evaluate the process of loading.

Such an evaluation of possible programming errors could be performed with an ammunition for measurements. An ammunition for mesurements would be based on complete 3P electronics and additional electronics for the evaluation of theprocess of loading.

The task for the master thesis has been to develop a lab-system to aid in the development of an ammunition for measurements.

This thesis describes with a introductory litterature study the work to create a lab-system. The constructed lab-system is based on an evaluation card including among other things a digital signal processor from the Blackfin family from Analog Devices. Tests and measurements show that the work has resulted in a well functioning lab-system, which meets the requirements of the task. In conclusion the thesis also describes comprehensively the remaining work to create a complete ammunition for measurements with the aid of the lab-system.

Abstract [sv]

Zonrorsammunitionen 3P programmeras under ans¨attning i pj¨as till ¨onskad funktionsmod. F¨or att s¨akerst¨alla att ammunitionen uppfattar samtliga programmeringssignaler korrekt och d¨armed kunna utesluta programmeringen som felk¨alla vid ett eventuellt felutfall finns ett behov att utv¨ardera laddningsf¨orloppet.

Med ett m¨atskott f¨or ammunitionen skulle en s°adan utv¨ardering av programmeringsfel kunna utf¨oras. Ett m¨atskott skulle bygga p°a komplett 3P-elektronik samt ytterligare elektronik f¨or utv¨ardering av laddningsf¨orloppet. Uppgiften f¨or examensarbetet har varit att utveckla ett labsystem som skall anv¨andas f¨or att m¨ojligg¨ora utvecklingen av ett m¨atskott.

Den h¨ar rapporten beskriver med hj¨alp av en inledande litteraturstudie arbetet med att skapa ett labsystem. Det konstruerade labsystemet ¨ar uppbyggt kring ett utv¨arderingskort inneh°allande bland annat en digital signalprocessor ur Blackfinfamiljen fr°an Analog Devices. Tester och m¨atningar visar att arbetet resulterat i ett v¨al fungerande labsystem, som uppfyller de krav som st¨allts p°a uppgiften. Avslutningsvis beskriver ¨aven rapporten ¨overgripande det arbete som°aterst°ar f¨or att med hj¨alp av labsystemet konstruera ett komplett m¨atskott.

Place, publisher, year, edition, pages
2005. , 84 p.
National Category
Engineering and Technology
URN: urn:nbn:se:liu:diva-97757ISRN: LITH-ITN-ED-EX--05/005--SEOAI: diva2:653189
Subject / course
Electrical Engineering
Available from: 2013-10-03 Created: 2013-09-23 Last updated: 2013-10-03Bibliographically approved

Open Access in DiVA

fulltext(806 kB)61 downloads
File information
File name FULLTEXT01.pdfFile size 806 kBChecksum SHA-512
Type fulltextMimetype application/pdf

Search in DiVA

By author/editor
Andersson, Jan-Erik
By organisation
Department of Science and TechnologyThe Institute of Technology
Engineering and Technology

Search outside of DiVA

GoogleGoogle Scholar
Total: 61 downloads
The number of downloads is the sum of all downloads of full texts. It may include eg previous versions that are now no longer available

Total: 35 hits
ReferencesLink to record
Permanent link

Direct link