Change search
ReferencesLink to record
Permanent link

Direct link
Analysis and control of drilling riser dynamics in dual gradient drilling
Norwegian University of Science and Technology, Faculty of Engineering Science and Technology, Department of Marine Technology.
2013 (English)MasteroppgaveStudent thesis
Abstract [en]

The aim of this thesis is to investigate a dual gradient riser system, adapted for operations in the Gulf of Mexico and subjected to first- and second-order wave forces, current and rig/vessel motion. Deep water drilling in narrow pressure zones pose several challenges for handling well pressure. Using two separate fluid volumes, in what is known as a dual gradient drilling (DGD) solution, the hydrostatic well pressure can be reduced by managing the return flow. To separate these volumes and control the mud return, the riser must accommodate a device known as a rotating control device (RCD). The RCD and the well pressure system extends the capabilities of conventional drilling schemes allowing for operations in deeper water and narrower pressure zones. The two volumes are closed off using a sealing element in the RCD, which holds the differential pressure created by the drilling system. The seal operate in a hostile environment resulting in extensive wear originating from abrasive particles, the rotating drillpipe and dynamic forces from the sheltering riser. The abrasion related to friction contact is strongly coupled with the riser and drillpipe contact and prompt the need for a closer analysis of the forces occurring between them. The riser system and RCD is therefore modelled in SIMA/RIFLEX and a dynamic analysis is carried out to obtain the lateral drillpipe/riser contact forces, indirectly finding the forces affecting the seal element. The analysis results indicate that the lateral force is below 4% of the seal element?s clamp force. The force magnitude is modest and will most likely have no significant impact on the operation. However, local forces and vibrations associated with resonance can create undesirable effects, which over time can lead to fatigue damage of the RCD and its subcomponents. Submerged equipment will be sensitive to range of resonance phenomena originating from the rig motions, second-order wave forces, current and vortex induced vibrations. This will encourage a review of the local dynamics and the potential use of riser control. Motivated by this, a finite element model is developed in Matlab/SIMULINK to study this in more detail. In order to de- tect resonance related vibrations, a modal decomposition model is formulated based on the finite element model. Using the modal model, a weighted estimate of the eigen frequencies active in the response can be provided to evaluate the resonance properties of the riser. To obtain a better understanding of the riser system and the control potential, a dynamic analysis of the models is carried out, focusing on low frequent rig/vessel motion. Both models are throughly verified using the commercial program RIFLEX, to ensure the sufficient accuracy. Inspired by the results from the analysis, control strategies based on manipulation of the resonance properties (modal con- trol) of the riser are examined, applied to a riser management system framework. The purpose of modal control is to increase safety margins and the operational economy, e.g. by reducing the time spent suspended because of seal element exchange or the risk for well head fatigue. Four different strategies based on manipulation of tension and position are proposed. Followed by a qualitative evaluation of the practical aspects, indicating that setpoint chasing and tension control are the most effective and attainable strategies available. The main contributions in this thesis are assessment of the lateral contact force associated with a deep water pipe-in-pipe dual gradient riser in the Gulf of Mexico, the development and verification of a extensive riser model using Matlab and SIMULINK, and the formulation of modal riser control for resonance vibrations in deep water drilling risers.

Place, publisher, year, edition, pages
Institutt for marin teknikk , 2013. , 134 p.
URN: urn:nbn:no:ntnu:diva-22358Local ID: ntnudaim:9330OAI: diva2:649601
Available from: 2013-09-19 Created: 2013-09-19 Last updated: 2013-09-19Bibliographically approved

Open Access in DiVA

fulltext(23987 kB)5840 downloads
File information
File name FULLTEXT01.pdfFile size 23987 kBChecksum SHA-512
Type fulltextMimetype application/pdf
cover(184 kB)24 downloads
File information
File name COVER01.pdfFile size 184 kBChecksum SHA-512
Type coverMimetype application/pdf
attachment(483 kB)60 downloads
File information
File name ATTACHMENT01.zipFile size 483 kBChecksum SHA-512
Type attachmentMimetype application/zip

By organisation
Department of Marine Technology

Search outside of DiVA

GoogleGoogle Scholar
Total: 5840 downloads
The number of downloads is the sum of all downloads of full texts. It may include eg previous versions that are now no longer available

Total: 330 hits
ReferencesLink to record
Permanent link

Direct link