Change search
ReferencesLink to record
Permanent link

Direct link
Physical Modeling and Simulation Analysis of an Advanced Automotive Racing Shock Absorber using the 1D Simulation Tool AMESim
Linköping University, Department of Management and Engineering, Fluid and Mechatronic Systems. Linköping University, The Institute of Technology. (The Institute of Technology)
2012 (English)Independent thesis Advanced level (degree of Master (Two Years)), 20 credits / 30 HE creditsStudent thesis
Abstract [en]

Shock absorbers are crucial components of a vehicle’s chassis responsible for the trade-off between stability, handling, and

passenger comfort. The aim of the thesis is to investigate the physical behavior of an advanced automotive racing shock

absorber, known as TTR, developed by Öhlins Racing AB. This goal is achieved by developing a detailed lumped parameter

numerical model of the entire TTR suspension in the advanced 1D simulation tool, AMESim.

The shock absorber is mainly composed of the main cylinder with through-rod piston design and the gas reservoir located at

the low pressure hydraulic line, which connects the compression and rebound sides. The mentioned sides are identical in terms

of the components which are a High Speed Adjuster, a Low Speed Adjuster, and a check valve mounted in parallel. The

adjusters are special hydraulic valves, which can be modified in terms of flow metering characteristics by means of external

accessible screws. Adjustment is done in a series of discrete numbers called ‘clicks’. A fixed orifice and a spring-loaded

poppet valve are responsible for controlling the piston low and high speed regions respectively.

The developed AMESim numerical model is capable of capturing the physics behind the real shock absorber damping

characteristics, under both static and dynamic conditions. The model is developed mainly using the standard AMESim

mechanical, hydraulic and hydraulic component design libraries and allows discovering the impact of each single hydraulic

component on the TTR overall behavior. In particular, the 1D model is presented in two levels of progressive physical

complexity in order to improve the dynamic damping characteristics. Several physical phenomena are considered, such as the

hydraulics volumes pressure dynamics, the contribution of external spring and pressure forces to the dynamic balance of the

moving elements, the static and viscous frictions, and the elastic deformations induced by solid boundaries pressure.

In this thesis, progressive model validation with different types of measurements is as well presented, covering the individual

hydraulic components models as well as the entire shock absorber model. The measurements have been performed on the flow

benches and dynamometers available at the Öhlins Racing measurements laboratory. These comparisons, deeply discussed in

the thesis, allow discovering the impact of specific physical effects on the low and high speed hydraulic valves static

performance and on the shock absorber dynamic behavior.

Numerical results show good agreement, especially at low and medium frequencies and symmetric ‘click’ adjustments on

compression and rebound sides. Further model development is necessary in the other areas, for example by considering more

complex models of the valve dynamics and fluid flow patterns, i.e. flow forces, together with more advanced models of the

sealing elements viscous friction, and thermal effects. Finally, the AMESim environments offered a good level of flexibility in

designing the TTR hydro-mechanical system, by allowing the user to choose between different levels of model complexity.

Place, publisher, year, edition, pages
2012. , 78 p.
Keyword [en]
Passive shock absorber, hydraulic, 1D modeling
National Category
Mechanical Engineering
URN: urn:nbn:se:liu:diva-92146ISRN: LIU-IEI-TEK-A--12/01408—SEOAI: diva2:620275
External cooperation
Öhlins Racing AB
Subject / course
Mechanical Engineering
2012-06-15, A39 (MASS), Department of Management and Engineering, Linköping University, SE-581 83 Linköping , Sweden, 13:15 (English)
Available from: 2013-05-08 Created: 2013-05-08 Last updated: 2013-05-08Bibliographically approved

Open Access in DiVA

M.Sadeghi_MS_Thesis(4298 kB)3025 downloads
File information
File name FULLTEXT01.pdfFile size 4298 kBChecksum SHA-512
Type fulltextMimetype application/pdf

Search in DiVA

By author/editor
Sadeghi Reineh, Maryam
By organisation
Fluid and Mechatronic SystemsThe Institute of Technology
Mechanical Engineering

Search outside of DiVA

GoogleGoogle Scholar
Total: 3029 downloads
The number of downloads is the sum of all downloads of full texts. It may include eg previous versions that are now no longer available

Total: 336 hits
ReferencesLink to record
Permanent link

Direct link