Change search
ReferencesLink to record
Permanent link

Direct link
Life Cycle Assessment of Norwegian Bioenergy Heat and Power Systems
Norwegian University of Science and Technology, Faculty of Engineering Science and Technology, Department of Energy and Process Engineering.
2012 (English)MasteroppgaveStudent thesis
Abstract [en]

This thesis assesses several value chains for bioenergy production in Norway and combines these representing two Norwegian scenarios. The environmental impacts are assessed using the methodology of life cycle assessment (LCA). A complete assessment of climate change impact has been a core task, and biogenic CO2 emissions are accounted for throughout the value chains investigated. Surface albedo effects are included in the assessment of forest resources. In addition to global warming potential, the value chains are assessed for three other impact categories; acidification potential, particulate matter formation potential and terrestrial ecotoxicity potential. Life cycle inventories are constructed for a set of six feedstocks, seven treatment options, ten energy conversion options and three energy distribution choices. The different options are then combined to 80 feasible value chains. Transport is included throughout all the value chains. All inventories are assembled to represent Norwegian conditions. Energy flows for the different value chains investigated are found to represent the current bioenergy system, with a potential increase for each value chain towards 2020 - representing the alternative scenario. Results are generated for the individual value chains, the reference scenario and the alternative scenario. The results show large differences between the different value chains. Energy wood and waste wood are the most beneficial feedstocks for bioenergy production, highly dependent on both the GWPbio factors utilised and inclusion of surface albedo effects. Pelletising is the pre-treatment option resulting in the lowest GWP, while integrated torrefaction and pelletising results in the highest GWP. Overall, a CHP plant with electricity demand is the most advantageous conversion route. A stand-alone thermal electricity plant has the definite highest impact, mainly because of low conversion efficiency. Heat distribution shows high impacts compared to electricity and steam distribution, and the resources resulting in lower impacts is therefore recommended as inputs for such units. Generally, handling of biogenic CO2 emissions is of high importance. The same is the case for surface albedo effects, changing the GWP for forest resources considerably. CHP plants are recommended for electricity production from biomass, and use of TOP, forest residues and stemwood are recommended to take place in the same conversion technology. The environmental impacts from a CHP plant is low, and TOP, forest residues and stemwood show high GWP. The GWP from energy wood, wood waste and pellets are low, and are therefore recommended for use in district heating plants. As stand-alone electricity production is not recommended, the GWP from a district heating plant is limited with the use of the mentioned resources. Pelletising is recommended for pre-treatment of Norwegian biomass because of low climate change impacts. The Norwegian Government has put forth ambitious goals to reduce the GHG emissions substantially towards 2020 and become climate neutral by 2030. The reference scenario assessed show a GWP of 134 grams CO2-equivalents per kWh, while the scenario for 2020 results in a climate change impact of 136 grams CO2-equivalents per kWh. Based on this, Norwegian bioenergy can offer a means to reduce the GHG emissions towards 2020, but because of considerable GWP from biogenic CO2 emissions, bioenergy should not be pursued for a goal of becoming climate neutral by 2030.

Place, publisher, year, edition, pages
Institutt for energi- og prosessteknikk , 2012. , 209 p.
Keyword [no]
ntnudaim:8421, MTENERG energi og miljø, Energi og samfunn
URN: urn:nbn:no:ntnu:diva-20382Local ID: ntnudaim:8421OAI: diva2:608896
Available from: 2013-03-01 Created: 2013-03-01 Last updated: 2013-06-12Bibliographically approved

Open Access in DiVA

fulltext(4396 kB)719 downloads
File information
File name FULLTEXT01.pdfFile size 4396 kBChecksum SHA-512
Type fulltextMimetype application/pdf
cover(184 kB)47 downloads
File information
File name COVER01.pdfFile size 184 kBChecksum SHA-512
Type coverMimetype application/pdf

By organisation
Department of Energy and Process Engineering

Search outside of DiVA

GoogleGoogle Scholar
Total: 719 downloads
The number of downloads is the sum of all downloads of full texts. It may include eg previous versions that are now no longer available

Total: 132 hits
ReferencesLink to record
Permanent link

Direct link