Change search
ReferencesLink to record
Permanent link

Direct link
Flexible active matrix addressed displays manufactured by printing and coating techniques
Linköping University, Department of Science and Technology. Linköping University, The Institute of Technology. Acreo AB, Sweden and Lintec Corporation, Japan.
Acreo AB, Sweden.
Acreo AB, Sweden.
Lintec Corporation, Japan.
Show others and affiliations
2013 (English)In: Journal of Polymer Science Part B: Polymer Physics, ISSN 0887-6266, E-ISSN 1099-0488, Vol. 51, no 4, 265-271 p.Article in journal (Refereed) Published
Abstract [en]

A flexible electrochromic active matrix addressed display, including 8 × 8 pixels, is demonstrated by using solution processing based on standard printing and coating manufacturing techniques. Each organic electrochromic display (OECD) pixel and its corresponding organic electrochemical transistor (OECT) are located on different sides of the flexible PET substrate. Electronic vias generated through the plastic substrate connects each OECD pixel with one addressing OECT. When comparing this display with actively addressed OECDs with all its components located on the same side, the present approach based on this electronic via substrate provides an enhanced pixel resolution and a relatively more simplified manufacturing process.

Place, publisher, year, edition, pages
Wiley-Blackwell , 2013. Vol. 51, no 4, 265-271 p.
Keyword [en]
electrochromic, flexible electronics, matrix display, organic electronics, printed electronics
National Category
Engineering and Technology
URN: urn:nbn:se:liu:diva-88353DOI: 10.1002/polb.23213ISI: 000313115500003OAI: diva2:602901

Funding Agencies|Lintec Corporation||VINNOVA (Printed Electronics Arena)||KAW (Power Papers)||Onnesjo Foundation||

Available from: 2013-02-04 Created: 2013-02-04 Last updated: 2015-05-06
In thesis
1. Novel architectures for flexible electrochemical devices and systems
Open this publication in new window or tab >>Novel architectures for flexible electrochemical devices and systems
2013 (English)Doctoral thesis, comprehensive summary (Other academic)
Abstract [en]

Electrically conducting polymers were discovered in the late 1970s. This finding generated a whole new research area named organic electronics, an area which has attracted great interest and tremendous achievements, in terms of devices and applications, have been reached by different research groups all over the world. Replacing inorganic materials by their organic counterparts in various kinds of electronic devices provides novel device functionalities as well as new opportunities in device manufacturing. One of the major advantages of utilizing organic materials in electronic devices is the high degree of freedom regarding fabrication methods. Since organic materials can be processed from solution various printing, coating and lamination techniques can be used to manufacture entire electronic systems on flexible carriers and substrates in a truly reel-to-reel fashion.

The main theme of this thesis relates to exploring novel device architectures to enable easy manufacturing of flexible electrochromic displays based on organic materials. After the introduction, the second part of the thesis treats some of the fundamentals of conducting polymers, and the third part explains the building blocks of matrix-addressed electrochromic displays: those systems combine electrochemical transistors and electrochromic display pixels. A brief introduction to printed electronics is also given in the fourth section. Then, active matrix addressed displays utilizing electronic vias manufactured through the substrate, which enable to use the substrate more efficiently in the resulting three-dimensional architecture, are presented in the fifth section. This novel system arrangement results in a matrix-addressed display with a relatively high fill-factor since its subcomponents are located on opposite sides of the substrate. The sixth section of the thesis is related to the achievement of passive matrix addressed displays. The architecture and the manufacturing process of these electrochromic displays are both very simple: an electrolyte is sandwiched in between the counter and the pixel electrode layers. The electrode materials chosen results in a non-linear current versus voltage characteristics, which enables matrix addressability also without the transistors. At last, in the seventh section, nanofibrillated cellulose (NFC) is used as the scaffold for either an electroactive polymer or the electrolyte. Various components, such as electrochromic pixels and electrochemical transistors, can be built from the resulting solid films thanks to the stable, soft and tacky properties of the hybridized NFC layer. Hence, a new concept for integration and reconfiguration of electronic systems consisting of electrochemical devices is achieved.

Place, publisher, year, edition, pages
Linköping: Linköping University Electronic Press, 2013. 70 p.
Linköping Studies in Science and Technology. Dissertations, ISSN 0345-7524 ; 1508
National Category
Engineering and Technology
urn:nbn:se:liu:diva-91273 (URN)978-91-7519-657-2 (print) (ISBN)
Public defence
2013-05-21, K1, Kåkenhus, Campus Norrköping, Linköpings universitet, Norrköping, 10:15 (English)
Available from: 2013-08-22 Created: 2013-04-18 Last updated: 2015-05-06Bibliographically approved

Open Access in DiVA

fulltext(334 kB)405 downloads
File information
File name FULLTEXT01.pdfFile size 334 kBChecksum SHA-512
Type fulltextMimetype application/pdf

Other links

Publisher's full text

Search in DiVA

By author/editor
Berggren, Magnus
By organisation
Department of Science and TechnologyThe Institute of TechnologyPhysics and Electronics
In the same journal
Journal of Polymer Science Part B: Polymer Physics
Engineering and Technology

Search outside of DiVA

GoogleGoogle Scholar
Total: 405 downloads
The number of downloads is the sum of all downloads of full texts. It may include eg previous versions that are now no longer available

Altmetric score

Total: 325 hits
ReferencesLink to record
Permanent link

Direct link