Change search
ReferencesLink to record
Permanent link

Direct link
Design and Characterization of a 6 W GaN HEMT Microwave Power Amplifier with Digital Predistortion Linearization
Norwegian University of Science and Technology, Faculty of Information Technology, Mathematics and Electrical Engineering, Department of Electronics and Telecommunications.
2011 (English)MasteroppgaveStudent thesis
Abstract [en]
In this thesis, characterization of a 6W GaN HEMT power amplifier for optimal operating conditions through load pull simulations and measurements is investigated. The purpose is to find source and load impedances to achieve for instance maximum efficiency and maximum output power, and investigate whether the simulated results can be replicated in a measurement setup. Simulations show that when matching for maximum output power, a peak output power of 13W is achieved, while in 1 dB compression, an output power of 11.40W together with a power added efficiency of nearly 67% is obtained, a remarkable for a 6W device. Matching for maximum efficiency yields a peak power added efficiency of 78% and a peak drain efficiency of 90 %, however, in 1 dB compressionthese levels are 71% and 74 %, respectively. Load pull measurements are performed with a prototype design, however, due to problems with the software controlling the measurement equipment, the tuning process had to be done manually, which effectively limited the possibility of replicating the simulated results. With manual tuning in coarse steps, two sets for semi–optimal operating conditions are found. For the first set of impedances, a peak output power greater than 11 W, with a peak power added efficiency of 68% is obtained, while for the second set of impedances, an output power of 7.40W with a peak power added efficiency of 70% is achieved. The measured performance indicate that the simulated results can be replicated once the measurement setup is working optimally. In addition, the topics of black–box characterization and digital predistortion linearization of microwave power amplifiers are investigated. Microwave power amplifiers obtain maximum operational performance when operated close to the saturation point. However, due to the nonlinear behavior of the device when operated in this region, the output signal will be distorted and cause interference with neighboring channels. Thus, in order to maintain the high operational performance and avoid adjacent channel interference, it is of great importance to characterize the nonlinear behavior of the device, and compensate for the introduced distortion terms. Digital predistortion linearization is considered to be among the most cost–effective linearization schemes as of today, providing flexibility and good performance. The design of a digital predistortion unit amounts to three main steps: deriving a behavioral model of the microwave power amplifier, estimating the model parameters for the inverse characteristic, and the implementation of the preinverse filter. For behavioral modeling, well–known nonlinear models, such as the Volterra series are investigated, and used with an indirect learning architecture to estimate the parameters of the inverse system. Simulations of the different linearization algorithms show that in an ideal environment, the adjacent channel power ratio can be reduced with up to 25 dB, almost independent of the model used for the predistorter design. However, when used in a real measurement setup, a maximum reduction in adjacent channel power ratio of only 15 dB is obtained. The relatively large difference in performance is most likely caused by a combination of long term memory effects due to semiconductor trapping phenomena, noise, and modeling errors.
Place, publisher, year, edition, pages
Institutt for elektronikk og telekommunikasjon , 2011. , 171 p.
Keyword [no]
ntnudaim:5254, SIE6 elektronikk, Radioteknikk og kommunikasjon
Identifiers
URN: urn:nbn:no:ntnu:diva-12612Local ID: ntnudaim:5254OAI: oai:DiVA.org:ntnu-12612DiVA: diva2:418965
Supervisors
Available from: 2011-05-24 Created: 2011-05-24

Open Access in DiVA

fulltext(19027 kB)2213 downloads
File information
File name FULLTEXT01.pdfFile size 19027 kBChecksum SHA-512
1e96eb6e53673eff49dc48499471a34975f8ea4f3d9a4aec89629d4a58852590df72e92aa95f9673c3300e1585442f5d340a017d951c49265bac0c33fb946ce4
Type fulltextMimetype application/pdf
cover(46 kB)30 downloads
File information
File name COVER01.pdfFile size 46 kBChecksum SHA-512
1f696a14e5d54051d1319fdd9363d061f41aa152aeeea41489c36c4963d5172f57df4e43a4711efd8aa10677c2d6c7224fc029f311b83e3d79b5d24836f2f2a6
Type coverMimetype application/pdf

By organisation
Department of Electronics and Telecommunications

Search outside of DiVA

GoogleGoogle Scholar
Total: 2213 downloads
The number of downloads is the sum of all downloads of full texts. It may include eg previous versions that are now no longer available

Total: 90 hits
ReferencesLink to record
Permanent link

Direct link