Change search
CiteExportLink to record
Permanent link

Direct link
Cite
Citation style
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Other style
More styles
Language
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Other locale
More languages
Output format
  • html
  • text
  • asciidoc
  • rtf
Mechanical Behavior of Uniformed Tailings Material in Triaxial Tests
Luleå University of Technology, Department of Civil, Environmental and Natural Resources Engineering, Mining and Geotechnical Engineering.ORCID iD: 0000-0002-5987-0006
Luleå University of Technology, Department of Civil, Environmental and Natural Resources Engineering, Mining and Geotechnical Engineering.ORCID iD: 0000-0002-3390-3113
Luleå University of Technology, Department of Civil, Environmental and Natural Resources Engineering, Mining and Geotechnical Engineering.ORCID iD: 0000-0002-1365-8552
2017 (English)In: The Electronic journal of geotechnical engineering, ISSN 1089-3032, E-ISSN 1089-3032, Vol. 22, no 06, p. 1717-1730Article in journal (Refereed) Published
Abstract [en]

Tailings dams are raised with time depending upon rate of generation of waste. A tailings dam can contain different particle sized materials within its dam body. The newly raised embankment in a tailings dam can be considered as vertical load being applied on subsequent layer. The applied loads can cause deformations and breakage of particles. The particle breakage can then lead to a skeleton with new particle size particles and hence can lead to new material properties. This paper provides the results from triaxial tests conducted on uniformed particle sizes as, 0.5mm-0.25mm, 0.25mm-0.125mm and 0.125mm-0.063mm.  The tests are performed at various effective radial stresses. The results are evaluated and compared with each particle size. The results include stress-strain and volumetric behavior during shearing, the effective stress ratio and stress-dilatancy plot. The friction angles are also evaluated and compared with different particle sized specimens. It was found that effective stress ratios were slightly higher when tests were performed at lower confining stresses and vice versa. It was also observed that particle size did not show any effect of friction angles.

Place, publisher, year, edition, pages
2017. Vol. 22, no 06, p. 1717-1730
Keyword [en]
Shear Strength, Triaxial Tests, Tailings Dams, Mechanical Properties, Tailings
National Category
Geotechnical Engineering
Research subject
Soil Mechanics
Identifiers
URN: urn:nbn:se:ltu:diva-62645OAI: oai:DiVA.org:ltu-62645DiVA, id: diva2:1084074
Note

Validerad; 2017; Nivå 1; 2017-04-03 (andbra)

Available from: 2017-03-23 Created: 2017-03-23 Last updated: 2018-04-17Bibliographically approved
In thesis
1. Mechanical Behavior of Tailings: Laboratory Tests from a Swedish Tailings Dam
Open this publication in new window or tab >>Mechanical Behavior of Tailings: Laboratory Tests from a Swedish Tailings Dam
2017 (English)Doctoral thesis, comprehensive summary (Other academic)
Abstract [en]

Tailings is leftover material from mining industry and is produced in huge quantities approximately 70-99% of the ore production.  Tailings material is stored as impoundments by constructing tailings dams which are often constructed with tailings material itself. Tailings are artificial material and the mechanical behavior of tailings material upon loading is different as compared to natural soil materials. There are number of dam failures reported every year which has severe impact on inhabitants and environment nearby. Considering the failures of tailings dams and consequences there is a need to understand the tailings material in depth for safe existence of these dams. The confident dam design can assure the safe existence of tailings dams for long term as these dams are presumed to function for generations to come. The material properties in tailings dams can change during operation due to raising of new layer. Raised new layer can change stress level, which in turn may change the material properties in terms of strength, pore pressures, grain sizes etc. Today mostly tailings dam are designed by performing analysis for safety for existing and future rasings as well. These analyses are based upon a for certain factor of safety. Not very much can be done with design and analysis for tailings material if the material is not described very well. Understanding of tailings material in depth can provide help for detailed material parameters which later can be used in safety assessment for future raising and changed conditions in dam.

This study presents the work carried out on tailings material from a Swedish tailings dam. The study is conducted on undisturbed and disturbed tailings material. The undisturbed tests are carried out to understand material properties as per in-situ conditions. Whereas disturbed materials are used to created different materials with different particles sizes. Initially in this study the basic properties of tailings materials are studied e.g. specific gravity, phase relationships, particle sizes, particle shapes and shear behavior on collected samples at various depths. During direct shear tests, the unexpected vertical height reductions were observed, these results are presented in this study. The comparison of strength parameters by direct shear and triaxial tests on material from various depths is also done and presented.

Based on results from direct shear, triaxial and oedometer tests on uniform sized tailings material; the evaluation of primary and secondary deformations and particle breakage and effect of vertical loads is also carried out and presented. The study also includes the comparison of strength parameters for each particles size. The breakage of particles is analyzed by sieving the material after direct shear tests followed by a particle shape study. The effect of deposition on shear strength parameters is also studied by construction of samples with different angle of deposition of material. The strength parameters of uniform sized particles in triaxial tests are also evaluated and discussed.

Place, publisher, year, edition, pages
Luleå: Luleå University of Technology, 2017
Series
Doctoral thesis / Luleå University of Technology 1 jan 1997 → …, ISSN 1402-1544
Keyword
Tailings dams, Tailings, Mechanical Behavior, Oedometer, Direct Shear, Triaxial, Shear strength
National Category
Geotechnical Engineering
Research subject
Soil Mechanics
Identifiers
urn:nbn:se:ltu:diva-62534 (URN)978-91-7583-849-6 (ISBN)978-91-7583-850-2 (ISBN)
Public defence
2017-04-25, F1031, Luleå tekninska universitet, Luleå, 10:00 (English)
Available from: 2017-03-20 Created: 2017-03-16 Last updated: 2017-11-24Bibliographically approved

Open Access in DiVA

fulltext(1109 kB)163 downloads
File information
File name FULLTEXT01.pdfFile size 1109 kBChecksum SHA-512
59999b05a3f7c57cf9c20dbde06dcbec47229684a2750de7acd3eb5256ac3045a1b09f4afeda18e080ce506b7449126572a69198f69a9adc500be3ebecd1ec1c
Type fulltextMimetype application/pdf

Other links

http://www.ejge.com/2017/Ppr2017.0165mb.pdf

Search in DiVA

By author/editor
Bhanbhro, RiazEdeskär, TommyKnutsson, Sven
By organisation
Mining and Geotechnical Engineering
In the same journal
The Electronic journal of geotechnical engineering
Geotechnical Engineering

Search outside of DiVA

GoogleGoogle Scholar
Total: 163 downloads
The number of downloads is the sum of all downloads of full texts. It may include eg previous versions that are now no longer available

urn-nbn

Altmetric score

urn-nbn
Total: 363 hits
CiteExportLink to record
Permanent link

Direct link
Cite
Citation style
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Other style
More styles
Language
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Other locale
More languages
Output format
  • html
  • text
  • asciidoc
  • rtf