Endre søk
RefereraExporteraLink to record
Permanent link

Direct link
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annet format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annet språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
Ultra high-pressure compaction of powder
Luleå tekniska universitet, Institutionen för teknikvetenskap och matematik, Material- och solidmekanik.ORCID-id: 0000-0002-4686-4010
2011 (engelsk)Doktoravhandling, med artikler (Annet vitenskapelig)
Abstract [en]

Sintering at high-pressure improves the properties of the material, either through new sintering aids becoming available or through improving intergranular bonding. This gives the manufactured products potential advantages like faster cut rates, and more precise and cleaner production methods that add up to cost efficiency and competitive edge. The production of synthetic diamond products demands tooling that can achieve high pressures and deliver it with a high degree of certainty. The common denominator for almost all high-pressure systems is to use capsules where a powder material encloses the core material. Numerical analysis of manufacturing processes with working conditions that reach ultra high pressure (above 10 GPa) requires a constitutive model that can handle the specific behaviours of the powder from a low density to solid state. The work in this thesis deals with characterization and simulation of the material behaviour during high-pressure compaction in powder pressing. Some of the work was focused on investigating the material when used as compressible gasket in high-pressure systems. The aim was to increase the knowledge of the high-pressure pressing process. This includes a better understanding of how mean stress develops in the compact during pressing and an insight into the development material models concerning highpressure materials. Both experimental and numerical investigations were made to gain knowledge in these fields. The mechanical behaviour of a CaCO3 powder mix was investigated using the Brazilian disc test, uniaxial compression testing and closed die experiments. The aim of the experimental work was to provide a foundation for numerical simulation of CaCO3 powder compaction at higher pressures. Friction measurements of the powder were also conducted. From the experimental investigations, density dependent material parameters were found. An elasto-plastic Cap model was developed for ultra high-pressure powder pressing. To improve the material model, density dependent constitutive parameters were included. The model was implemented as a user-defined material subroutine in a nonlinear finite element program. The model was validated against pressure measurements using phase transitions of Bismuth. The measurements were conducted in a Bridgman anvil apparatus. The simulations showed that thin discs with small radial extrusion generate a plateau at a low-pressure level, while thick discs with large radial extrusion generate a pressure peak at a high-pressure level. The results showed that FE-results can be used to engineer pressure peaks needed to seal HPHT-systems. For compressible gaskets, it was found that diametral support increases the phase transformation load. Higher initial density of the powder compact and diametral support generate higher pressure per unit thickness. The results from the validation using pressure measurements showed that the simulation model was indeed capable of reproducing load–thickness curves and pressure profiles, up to 9 GPa, close to the experimental curves.

sted, utgiver, år, opplag, sider
Luleå: Luleå tekniska universitet, 2011.
Serie
Doctoral thesis / Luleå University of Technology 1 jan 1997 → …, ISSN 1402-1544
HSV kategori
Forskningsprogram
Hållfasthetslära
Identifikatorer
URN: urn:nbn:se:ltu:diva-16908Lokal ID: 09cc3472-02a3-49b9-82f5-a08b49f2817cISBN: 978-91-7439-346-0 (tryckt)OAI: oai:DiVA.org:ltu-16908DiVA, id: diva2:989895
Merknad
Godkänd; 2011; 20111020 (bersve); DISPUTATION Ämnesområde: Hållfasthetslära/Solid Mechanics Opponent: Professor Javier Oliver, Dept of Strength of Materials and Structural Analysis, Technical University of Catalonia, Barcelona, Spain, Ordförande: Bitr professor Pär Jonsén, Institutionen för teknikvetenskap och matematik, Luleå tekniska universitet Tid: Torsdag den 15 december 2011, kl 09.00 Plats: E246, Luleå tekniska universitetTilgjengelig fra: 2016-09-29 Laget: 2016-09-29 Sist oppdatert: 2017-11-24bibliografisk kontrollert

Open Access i DiVA

fulltekst(23478 kB)323 nedlastinger
Filinformasjon
Fil FULLTEXT01.pdfFilstørrelse 23478 kBChecksum SHA-512
4cf124aa9598a203080186ff16839cc006ccd09974adaa2bc8f3a1994f6542f16e7adb58503cb1560c52b714f6150bc4568e81b82796827e28eeadc4a8abff7c
Type fulltextMimetype application/pdf
fulltekst(23805 kB)65 nedlastinger
Filinformasjon
Fil FULLTEXT02.pdfFilstørrelse 23805 kBChecksum SHA-512
dda2cba92ecf26c53707dae3745d75adfa7f6814a79cf816444251e6b0624cd2210ec0bdc728b349861fe5fd666f81285b8eb2989e6adedbf1722cc0a84810cf
Type fulltextMimetype application/pdf

Søk i DiVA

Av forfatter/redaktør
Berg, Sven
Av organisasjonen

Søk utenfor DiVA

GoogleGoogle Scholar
Totalt: 388 nedlastinger
Antall nedlastinger er summen av alle nedlastinger av alle fulltekster. Det kan for eksempel være tidligere versjoner som er ikke lenger tilgjengelige

isbn
urn-nbn

Altmetric

isbn
urn-nbn
Totalt: 449 treff
RefereraExporteraLink to record
Permanent link

Direct link
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annet format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annet språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf