Ändra sökning
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
Mould susceptibility of Scots pine (Pinus sylvestris L.) sapwood: Impact of drying, thermal modification, and copper-based preservative
Luleå tekniska universitet, Institutionen för teknikvetenskap och matematik, Träteknologi.
Luleå tekniska universitet, Institutionen för teknikvetenskap och matematik, Träteknologi.ORCID-id: 0000-0002-3544-8716
Luleå tekniska universitet, Institutionen för teknikvetenskap och matematik, Träteknologi.
2013 (Engelska)Ingår i: International Biodeterioration & Biodegradation, ISSN 0964-8305, E-ISSN 1879-0208, Vol. 85, s. 284-288Artikel i tidskrift (Refereegranskat) Published
Abstract [en]

The development of mould on wood surfaces depends on several factors. Although mould does not affect the mechanical properties of wood, it greatly reduces the aesthetic value of wood like the sapwood of Scots pine (Pinus sylvestris L.), which is very prone to mould. In addition, adverse health effects of mould on humans are also a great concern. Different types of dried and treated wood were used to observe whether they had enhanced durability against mould following an accelerated laboratory test method in a climate chamber. Samples were green, air-dried, industrially thermally-modified, treated with copper-based preservative, and kiln-dried wood, which were tested within a single test run. The test produced the following main results: the thermal modification increased the durability of the wood, and the protective effectiveness of alternative treatments was comparable to that of commercially available copper-based treatment. However, the initial moisture content of the samples during mould exposure had a great influence on the onset of mould growth. The risk of mould susceptibility of industrial kiln-dried lumber can be reduced by drying using the double-layering technique which likely forced the nutrients to deposit near the evaporation surfaces followed by planing off the nutrient enriched edges.

Ort, förlag, år, upplaga, sidor
2013. Vol. 85, s. 284-288
Nationell ämneskategori
Biomaterial
Forskningsämne
Träfysik
Identifikatorer
URN: urn:nbn:se:ltu:diva-12380DOI: 10.1016/j.ibiod.2013.06.031ISI: 000327166300039Scopus ID: 2-s2.0-84884246330Lokalt ID: b84bb295-5eee-4f48-babb-1a3ab3acb148OAI: oai:DiVA.org:ltu-12380DiVA, id: diva2:985330
Anmärkning
Validerad; 2013; 20130607 (sheahm)Tillgänglig från: 2016-09-29 Skapad: 2016-09-29 Senast uppdaterad: 2018-07-10Bibliografiskt granskad

Open Access i DiVA

Fulltext saknas i DiVA

Övriga länkar

Förlagets fulltextScopus

Sök vidare i DiVA

Av författaren/redaktören
Ahmed, Sheikh AliSehlstedt-Persson, MargotMorén, Tom
Av organisationen
Träteknologi
I samma tidskrift
International Biodeterioration & Biodegradation
Biomaterial

Sök vidare utanför DiVA

GoogleGoogle Scholar

doi
urn-nbn

Altmetricpoäng

doi
urn-nbn
Totalt: 870 träffar
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf