Ändra sökning
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
Anatomical properties and process parameters affecting blister/blow formation in densified European aspen and downy birch sapwood boards by thermo-hygro-mechanical compression
Luleå tekniska universitet, Institutionen för teknikvetenskap och matematik, Träteknologi.
Luleå tekniska universitet, Institutionen för teknikvetenskap och matematik, Träteknologi.
Luleå tekniska universitet, Institutionen för teknikvetenskap och matematik, Träteknologi.ORCID-id: 0000-0001-8404-7356
Wood Research Center (CRB), Department of Wood and Forest Sciences, Faculty of Forestry, Geography and Geomatics, Laval University, Quebec.
Visa övriga samt affilieringar
2013 (Engelska)Ingår i: Journal of Materials Science, ISSN 0022-2461, E-ISSN 1573-4803, Vol. 48, nr 24, s. 8571-8579Artikel i tidskrift (Refereegranskat) Published
Abstract [en]

Approximately, 13.5 % of the standing volume of productive forest land in Sweden is covered by birch and aspen, which provides the vast potential to produce value-added products such as densified wood. This study shows whether it is possible to densify those species with a thermo-hygro-mechanical (THM) process using heat, steam, and pressure. In this process, transverse compression on thin European aspen (Populus tremula) and downy birch (Betula pubescens) boards was performed at 200 ºC with a maximum steam pressure of 550 kPa. To obtain a theoretical 50 % compression set, the press’s maximum hydraulic pressure ranged from 1.5 to 7.3 MPa. Preliminary tests showed that ~75 % of the birch boards produced defects (blisters/blows) while only 25 % of the aspen boards did. Mainly, radial delamination associated with internal checks in intrawall and transwall fractures caused small cracks (termed blisters) while blows are characterized by relatively larger areas of delamination visible as a bumpy surface on the panel. Anatomical investigations revealed that birch was more prone to those defects than aspen. However, those defects could be minimized by increasing the pre-treatment time during the THM processing.

Ort, förlag, år, upplaga, sidor
2013. Vol. 48, nr 24, s. 8571-8579
Nationell ämneskategori
Biomaterial Annan maskinteknik
Forskningsämne
Träfysik; Träproduktutveckling
Identifikatorer
URN: urn:nbn:se:ltu:diva-7066DOI: 10.1007/s10853-013-7679-9ISI: 000324111700028Scopus ID: 2-s2.0-84891903228Lokalt ID: 5618af53-b6b8-496d-a902-97c101649a98OAI: oai:DiVA.org:ltu-7066DiVA, id: diva2:979953
Anmärkning
Validerad; 2013; 20130823 (sheahm)Tillgänglig från: 2016-09-29 Skapad: 2016-09-29 Senast uppdaterad: 2018-07-10Bibliografiskt granskad

Open Access i DiVA

Fulltext saknas i DiVA

Övriga länkar

Förlagets fulltextScopus

Sök vidare i DiVA

Av författaren/redaktören
Ahmed, Sheikh AliMorén, TomHagman, OlleElustondo, Diego
Av organisationen
Träteknologi
I samma tidskrift
Journal of Materials Science
BiomaterialAnnan maskinteknik

Sök vidare utanför DiVA

GoogleGoogle Scholar

doi
urn-nbn

Altmetricpoäng

doi
urn-nbn
Totalt: 1646 träffar
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf