Ändra sökning
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
Selecting benchmarks for reactor simulations: an application to a Lead Fast Reactor
Uppsala universitet, Teknisk-naturvetenskapliga vetenskapsområdet, Fysiska sektionen, Institutionen för fysik och astronomi, Tillämpad kärnfysik. (Nuclear Research Group)
Uppsala universitet, Teknisk-naturvetenskapliga vetenskapsområdet, Fysiska sektionen, Institutionen för fysik och astronomi, Tillämpad kärnfysik. (Nuclear Reactions Group)
Uppsala universitet, Teknisk-naturvetenskapliga vetenskapsområdet, Fysiska sektionen, Institutionen för fysik och astronomi, Tillämpad kärnfysik. (Nuclear Reactions Group)
Uppsala universitet, Teknisk-naturvetenskapliga vetenskapsområdet, Fysiska sektionen, Institutionen för fysik och astronomi, Tillämpad kärnfysik. (Nuclear Reaction Group)
Visa övriga samt affilieringar
2016 (Engelska)Ingår i: Annals of Nuclear Energy, ISSN 0306-4549, E-ISSN 1873-2100, Vol. 96, s. 158-169Artikel i tidskrift (Refereegranskat) Published
Abstract [en]

For several decades reactor design has been supported by computer codes for the investigation of reactor behavior under both steady state and transient conditions. The use of computer codes to simulate reactor behavior enables the investigation of various safety scenarios saving time and cost. There has been an increase in the development of in-house (local) codes by various research groups in recent times for preliminary design of specific or targeted nuclear reactor applications. These codes must be validated and calibrated against experimental benchmark data with their evolution and improvements. Given the large number of benchmarks available, selecting these benchmarks for reactor calculations and validation of simulation codes for specific or target applications can be rather tedious and difficult. In the past, the traditional approach based on expert judgement using information provided in various handbooks, has been used for the selection of these benchmarks. This approach has been criticized because it introduces a user bias into the selection process. This paper presents a method for selecting these benchmarks for reactor calculations for specific reactor applications based on the Total Monte Carlo (TMC) method. First, nuclear model parameters are randomly sampled within a given probability distribution and a large set of random nuclear data files are produced using the TALYS code system. These files are processed and used to analyze a target reactor system and a set of criticality benchmarks. Similarity between the target reactor system and one or several benchmarks is quantified using a similarity index. The method has been applied to the European Lead Cooled Reactor (ELECTRA) and a set of plutonium and lead sensitive criticality benchmarks using the effective multiplication factor (keffkeff). From the study, strong similarity were observed in the keffkeff between ELECTRA and some plutonium and lead sensitive criticality benchmarks. Also, for validation purposes, simulation results for a list of selected criticality benchmarks simulated with the MCNPX and SERPENT codes using different nuclear data libraries have been compared with experimentally measured benchmark keff values.

Ort, förlag, år, upplaga, sidor
2016. Vol. 96, s. 158-169
Nyckelord [en]
Benchmark selection; Criticality benchmarks; Random nuclear data; Total Monte Carlo (TMC); Code validation
Nationell ämneskategori
Subatomär fysik
Identifikatorer
URN: urn:nbn:se:uu:diva-264414DOI: 10.1016/j.anucene.2016.05.033ISI: 000380600300017OAI: oai:DiVA.org:uu-264414DiVA, id: diva2:860205
Forskningsfinansiär
VetenskapsrådetTillgänglig från: 2015-10-11 Skapad: 2015-10-11 Senast uppdaterad: 2017-12-01Bibliografiskt granskad
Ingår i avhandling
1. Nuclear data uncertainty quantification and data assimilation for a lead-cooled fast reactor: Using integral experiments for improved accuracy
Öppna denna publikation i ny flik eller fönster >>Nuclear data uncertainty quantification and data assimilation for a lead-cooled fast reactor: Using integral experiments for improved accuracy
2015 (Engelska)Doktorsavhandling, sammanläggning (Övrigt vetenskapligt)
Abstract [en]

For the successful deployment of advanced nuclear systems and optimization of current reactor designs, high quality nuclear data are required. Before nuclear data can be used in applications they must first be evaluated, tested and validated against a set of integral experiments, and then converted into formats usable for applications. The evaluation process in the past was usually done by using differential experimental data which was then complemented with nuclear model calculations. This trend is fast changing due to the increase in computational power and tremendous improvements in nuclear reaction models over the last decade. Since these models have uncertain inputs, they are normally calibrated using experimental data. However, these experiments are themselves not exact. Therefore, the calculated quantities of model codes such as cross sections and angular distributions contain uncertainties. Since nuclear data are used in reactor transport codes as input for simulations, the output of transport codes contain uncertainties due to these data as well. Quantifying these uncertainties is important for setting safety margins; for providing confidence in the interpretation of results; and for deciding where additional efforts are needed to reduce these uncertainties. Also, regulatory bodies are now moving away from conservative evaluations to best estimate calculations that are accompanied by uncertainty evaluations.

In this work, the Total Monte Carlo (TMC) method was applied to study the impact of nuclear data uncertainties from basic physics to macroscopic reactor parameters for the European Lead Cooled Training Reactor (ELECTRA). As part of the work, nuclear data uncertainties of actinides in the fuel, lead isotopes within the coolant, and some structural materials have been investigated. In the case of the lead coolant it was observed that the uncertainty in the keff and the coolant void worth (except in the case of 204Pb), were large, with the most significant contribution coming from 208Pb. New 208Pb and 206Pb random nuclear data libraries with realistic central values have been produced as part of this work. Also, a correlation based sensitivity method was used in this work, to determine parameter - cross section correlations for different isotopes and energy groups.

Furthermore, an accept/reject method and a method of assigning file weights based on the likelihood function are proposed for uncertainty reduction using criticality benchmark experiments within the TMC method. It was observed from the study that a significant reduction in nuclear data uncertainty was obtained for some isotopes for ELECTRA after incorporating integral benchmark information. As a further objective of this thesis, a method for selecting benchmark for code validation for specific reactor applications was developed and applied to the ELECTRA reactor. Finally, a method for combining differential experiments and integral benchmark data for nuclear data adjustments is proposed and applied for the adjustment of neutron induced 208Pb nuclear data in the fast energy region.

Ort, förlag, år, upplaga, sidor
Uppsala: Acta Universitatis Upsaliensis, 2015. s. 85
Serie
Digital Comprehensive Summaries of Uppsala Dissertations from the Faculty of Science and Technology, ISSN 1651-6214 ; 1315
Nyckelord
Total Monte Carlo, ELECTRA, nuclear data, uncertainty propagation, integral experiments, nuclear data adjustment, uncertainty reduction
Nationell ämneskategori
Subatomär fysik
Identifikatorer
urn:nbn:se:uu:diva-265502 (URN)978-91-554-9407-0 (ISBN)
Disputation
2015-12-17, polhemsalen, Ångströmlaboratoriet, Lägerhyddsvägen 1, Uppsala, 09:15 (Engelska)
Opponent
Handledare
Tillgänglig från: 2015-11-24 Skapad: 2015-10-30 Senast uppdaterad: 2016-01-13

Open Access i DiVA

Fulltext saknas i DiVA

Övriga länkar

Förlagets fulltext

Sök vidare i DiVA

Av författaren/redaktören
Alhassan, ErwinSjöstrand, HenrikHelgesson, PetterÖsterlund, MichaelPomp, StephanArjan, J. Koning
Av organisationen
Tillämpad kärnfysik
I samma tidskrift
Annals of Nuclear Energy
Subatomär fysik

Sök vidare utanför DiVA

GoogleGoogle Scholar

doi
urn-nbn

Altmetricpoäng

doi
urn-nbn
Totalt: 879 träffar
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf