Endre søk
RefereraExporteraLink to record
Permanent link

Direct link
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annet format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annet språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
Estimation of the pore volume at the interface between paper web and press felt
Uppsala universitet, Teknisk-naturvetenskapliga vetenskapsområdet, Matematisk-datavetenskapliga sektionen, Centrum för bildanalys. Uppsala universitet, Teknisk-naturvetenskapliga vetenskapsområdet, Matematisk-datavetenskapliga sektionen, Institutionen för informationsteknologi, Datoriserad bildanalys.
Uppsala universitet, Teknisk-naturvetenskapliga vetenskapsområdet, Matematisk-datavetenskapliga sektionen, Centrum för bildanalys.
2006 (engelsk)Inngår i: Nordic Pulp & Paper Research Journal, ISSN 0283-2631, E-ISSN 2000-0669, Vol. 21, nr 3, s. 395-402Artikkel i tidsskrift (Fagfellevurdert) Published
Abstract [en]

A method for determining the water content at the interface between a press felt and a paper web has been developed. The water content was obtained by subtracting the estimated volume of the indented fibre web from the measured felt surface porosity of the press felt. The felt surface porosity was calculated from a topography map that was imaged with a Confocal Laser Scanning Microscope (CLSM) method. Here, the press felt was compressed against a smooth surface using a stress in the range of 0 to 10 MPa. Artefacts in the CLSM images were reduced using an image analysis method. The indentation of paper webs into the measured felt surface pores at different applied pressures was estimated using another image analysis method, simulating a rolling ball, with different radii of curvature for the different pressures and grammages, rolling over the felt surface. The ball radii were determined for a low and a high grammage web using the STFI-Packforsk Dewatering model. The method was evaluated in a case study with four press felts that had batt fibre diameters in a range between 22 and 78 μm. The indentation was calculated for webs with a low (15 g/m2) and a high grammage (105 g/m2), respectively. The evaluation showed that a considerable amount of porespace is available at the interface between the web and the felt. In most cases, the volume of the water-filled pores accounted for approximately 50% of the total surface porosity of the felt. Assuming a complete water saturation of the web/felt interface, approximately 10 g/m2 of water for the finest felt surface up to 40 g/m2 for the coarsest felt surface, could be located at the interface between the press felt and the paper web at a load of 10 MPa. This implies that a considerable amount of water is available for separation rewetting.

sted, utgiver, år, opplag, sider
2006. Vol. 21, nr 3, s. 395-402
Emneord [en]
press felt, surface porosity, pore volume estimation, image analysis, CLSM, compression device
HSV kategori
Identifikatorer
URN: urn:nbn:se:uu:diva-18439ISI: 000241531500015OAI: oai:DiVA.org:uu-18439DiVA, id: diva2:46211
Tilgjengelig fra: 2006-12-21 Laget: 2006-12-21 Sist oppdatert: 2018-01-12bibliografisk kontrollert

Open Access i DiVA

Fulltekst mangler i DiVA

Søk i DiVA

Av forfatter/redaktør
Axelsson, MariaÖstlund, CatherineSvensson, Stina
Av organisasjonen
I samme tidsskrift
Nordic Pulp & Paper Research Journal

Søk utenfor DiVA

GoogleGoogle Scholar

urn-nbn

Altmetric

urn-nbn
Totalt: 716 treff
RefereraExporteraLink to record
Permanent link

Direct link
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annet format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annet språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf