Digitala Vetenskapliga Arkivet

Endre søk
RefereraExporteraLink to record
Permanent link

Direct link
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annet format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annet språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
Process stability during fiber laser-arc hybrid welding of thick steel plates
Norwegian University of Science and Technology, Department of Engineering Design and Materials.
Luleå tekniska universitet, Institutionen för teknikvetenskap och matematik, Produkt- och produktionsutveckling.ORCID-id: 0000-0003-4265-1541
Norwegian University of Science and Technology, Department of Engineering Design and Materials.
Luleå tekniska universitet, Institutionen för teknikvetenskap och matematik, Produkt- och produktionsutveckling.ORCID-id: 0000-0002-3569-6795
2018 (engelsk)Inngår i: Optics and lasers in engineering, ISSN 0143-8166, E-ISSN 1873-0302, Vol. 102, s. 34-44Artikkel i tidsskrift (Fagfellevurdert) Published
Abstract [en]

TThick steel plates are frequently used in shipbuilding, pipelines and other related heavy industries, and are usually joined by arc welding. Deep penetration laser-arc hybrid welding could increase productivity but has not been thoroughly investigated, and is therefore usually limited to applications with medium thickness (5-15 mm) sections. A major concern is process stability, especially when using modern welding consumables such as metal-cored wire and advanced welding equipment. High speed imaging allows direct observation of the process so that process behavior and phenomena can be studied. In this paper, 45 mm thick high strength steel was welded (butt joint double-sided) using the fiber laser-MAG hybrid process utilizing a metal-cored wire without pre-heating. Process stability was monitored under a wide range of welding parameters. It was found that the technique can be used successfully to weld thick sections with appropriate quality when the parameters are optimized. When comparing conventional pulsed and the more advanced cold metal transfer pulse (CMT+P) arc modes, it was found that both can provide high quality welds. CMT+P arc mode can provide more stable droplet transfer over a limited range of travel speeds. At higher travel speeds, an unstable metal transfer mechanism was observed. Comparing leading arc and trailing arc arrangements, the leading arc configuration can provide higher quality welds and more stable processing at longer inter-distances between the heat sources.

sted, utgiver, år, opplag, sider
Elsevier, 2018. Vol. 102, s. 34-44
HSV kategori
Forskningsprogram
Produktionsutveckling
Identifikatorer
URN: urn:nbn:se:ltu:diva-66398DOI: 10.1016/j.optlaseng.2017.10.020ISI: 000418970600005Scopus ID: 2-s2.0-85032330245OAI: oai:DiVA.org:ltu-66398DiVA, id: diva2:1154985
Merknad

Validerad;2017;Nivå 2;2017-11-06 (andbra)

Tilgjengelig fra: 2017-11-06 Laget: 2017-11-06 Sist oppdatert: 2018-01-23bibliografisk kontrollert

Open Access i DiVA

Fulltekst mangler i DiVA

Andre lenker

Forlagets fulltekstScopus

Søk i DiVA

Av forfatter/redaktør
Frostevarg, JanKaplan, Alexander
Av organisasjonen
I samme tidsskrift
Optics and lasers in engineering

Søk utenfor DiVA

GoogleGoogle Scholar

doi
urn-nbn

Altmetric

doi
urn-nbn
Totalt: 595 treff
RefereraExporteraLink to record
Permanent link

Direct link
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annet format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annet språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf