Endre søk
RefereraExporteraLink to record
Permanent link

Direct link
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annet format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annet språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
Influence of tool steel hard phase orientation and shape on galling
Department of Mechanical and Materials Engineering, Karlstad University, Karlstad, Sweden.ORCID-id: 0000-0002-8144-8821
Department of Mechanical and Materials Engineering, Karlstad University, Karlstad, Sweden.
Department of Mechanical and Materials Engineering, Karlstad University, Karlstad, Sweden.
Department of Mechanical and Materials Engineering, Karlstad University, Karlstad, Sweden.
2014 (engelsk)Inngår i: Advanced Materials Research, ISSN 1022-6680, E-ISSN 1662-8985, Vol. 966-96, s. 249-258Artikkel i tidsskrift (Fagfellevurdert) Published
Abstract [en]

Conventionally manufactured cold work tool steel is often used in sheet metal forming as die material. Due to the forging process, the as-cast network structure of carbides is broken into elongated particles. Depending on the tool cross-section, the orientation and shape of carbides in the active tool surface is different. In the present research, the influence of tool steel hard phase orientation and shape on galling was investigated. D2 type tool steel was cut in three different orientations and tested in lubricated sliding conditions against AISI 304 austenitic stainless steel. Tests were performed using a Slider-On-Flat-Surface and galling was detected by changes in friction and post-test microscopy. The lubricant was Castrol FST8 using 5 g/m2 sheet material. Results showed a strong correlation between sliding distance to galling and tool steel hard phase orientation and shape at low loads, whereas high load contact resulted in early galling in all cases. Material transfer was observed mainly to the tool steel matrix. The worst performance was observed for specimens cut so that the tool steel hard phase, M7C3 carbides in the D2 steel, were oriented along the sliding direction, which resulted in longer open tool matrix areas contacting the sheet material.

sted, utgiver, år, opplag, sider
Trans Tech Publications, 2014. Vol. 966-96, s. 249-258
Emneord [en]
Austenitic stainless steel; Carbides; Industrial engineering; Joining; Lubricants; Plastic deformation; Production engineering; Sheet metal; Tribology; Wear of materials, Cold work tool steels; Elongated particles; Galling; Material transfers; Metal transfers; Network structures; Sliding conditions; Strong correlation, Tool steel
HSV kategori
Forskningsprogram
Maskinteknik
Identifikatorer
URN: urn:nbn:se:oru:diva-58820DOI: 10.4028/www.scientific.net/AMR.966-967.249Scopus ID: 2-s2.0-84904014001OAI: oai:DiVA.org:oru-58820DiVA, id: diva2:1128250
Tilgjengelig fra: 2014-05-19 Laget: 2017-07-24 Sist oppdatert: 2019-03-05bibliografisk kontrollert

Open Access i DiVA

Fulltekst mangler i DiVA

Andre lenker

Forlagets fulltekstScopus

Søk i DiVA

Av forfatter/redaktør
Karlsson, Patrik
I samme tidsskrift
Advanced Materials Research

Søk utenfor DiVA

GoogleGoogle Scholar

doi
urn-nbn

Altmetric

doi
urn-nbn
Totalt: 377 treff
RefereraExporteraLink to record
Permanent link

Direct link
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annet format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annet språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf