Endre søk
RefereraExporteraLink to record
Permanent link

Direct link
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annet format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annet språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
Model based analysis of coupled vibrations due to the combi-bearing in vertical hydroturbogenerator rotors
Luleå tekniska universitet, Material- och solidmekanik.
Luleå tekniska universitet, Material- och solidmekanik.
Vattenfall Research & Development.
2011 (engelsk)Inngår i: Journal of Vibration and Acoustics-Transactions of the ASME, ISSN 1048-9002, E-ISSN 1528-8927, Vol. 133, nr 6, artikkel-id 61012Artikkel i tidsskrift (Fagfellevurdert) Published
Abstract [en]

The studies presented in this paper focus on analyzing how the combined thrust-journal bearing (commonly called combi-bearing) influences the dynamics of hydropower rotors. Thrust bearing is a component used in vertical rotating machinery and shafts designed to transmit thrust. The total axial load is carried by the single thrust bearing. Any design, manufacture, or assembly error in this component (thrust bearing) would certainly influence the functionality of the entire machine. The analyzed combi-bearing is an existing machine component used in the hydropower unit Porjus U9 situated in northern Sweden. This combi-bearing is a fluid-film lubricated tilting-pad thrust and journal bearings combined together. Only linear fluid-film stiffness was taken into account in the model while fluid-film damping and pads inertia effects were not taken into account. The linearized model shows that the combi-bearing couples the rotor's lateral and angular motions. However, if the thrust bearing's pads arrangement is not symmetrical or if all the pads are not angularly equidistant the rotor axial and angular motions are also coupled. This last case of coupling will also occur if the thrust bearing equivalent total stiffness is not evenly distributed over the thrust bearing. A defective pad or unequal hydrodynamic pressure distribution on the pads' surfaces may be the cause. The Porjus U9's simulation results show that the combi-bearing influences the dynamic behavior of the machine. The rotor motions' coupling due to combi-bearing changes the system's natural frequencies and vibration modes.

sted, utgiver, år, opplag, sider
2011. Vol. 133, nr 6, artikkel-id 61012
HSV kategori
Forskningsprogram
Hållfasthetslära
Identifikatorer
URN: urn:nbn:se:hb:diva-11481DOI: 10.1115/1.4005002Lokal ID: d3273dd7-f21f-412a-b20d-f77d26708fdeOAI: oai:DiVA.org:hb-11481DiVA, id: diva2:1057039
Merknad

Validerad; 2011; 20111212 (jealun)

Tilgjengelig fra: 2016-09-29 Laget: 2016-12-16 Sist oppdatert: 2018-05-08bibliografisk kontrollert

Open Access i DiVA

Fulltekst mangler i DiVA

Andre lenker

Forlagets fulltekst

Søk i DiVA

Av forfatter/redaktør
Luneno, Jean-Claude
I samme tidsskrift
Journal of Vibration and Acoustics-Transactions of the ASME

Søk utenfor DiVA

GoogleGoogle Scholar

doi
urn-nbn

Altmetric

doi
urn-nbn
Totalt: 14 treff
RefereraExporteraLink to record
Permanent link

Direct link
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annet format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annet språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf