Ändra sökning
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
TMP properties and refining conditions in a CD82 chip refiner. Part I: Step changes of process variables, description of the tests
Mittuniversitetet, Fakulteten för naturvetenskap, teknik och medier, Avdelningen för kemiteknik. StoraEnso Kvarnsveden, Borlänge.
Mittuniversitetet, Fakulteten för naturvetenskap, teknik och medier, Avdelningen för kemiteknik.
QualTech AB, Tyringe.
Chalmers University of Technology, Gothenburg.
Visa övriga samt affilieringar
2018 (Engelska)Ingår i: Nordic Pulp & Paper Research Journal, ISSN 0283-2631, E-ISSN 2000-0669, Vol. 33, nr 1, s. 69-81Artikel i tidskrift (Refereegranskat) Published
Abstract [en]

The study explores how changes in process variables, residence time and pulp consistency in refining influence the pulp properties. The equipment utilized in this study was a conical disc chip refiner (RGP82CD) producing thermomechanical pulp (TMP). The focus was on the ratio between tensile index and specific energy consumption. Pulp properties were measured for composite pulp samples taken from the refiner blow line. Residence times and pulp consistencies were estimated by use of the extended entropy model. This showed that the CD-refiner, with the flat and conical refining zone, has a process performance similar to that of a two-stage refiner set-up, and that the consistency in both refining zones is of high importance. Comparing different periods revealed that even if the values of measured blow line consistency are similar, significant differences in the estimated consistency in the flat zone can prevail. Therefore, only monitoring blow line consistency is not enough. Specifically, it was found that the pulp consistency after the flat zone could be very high, considerably higher than in the blow line, and this could have negative effects on tensile index and fibre length. 

Ort, förlag, år, upplaga, sidor
2018. Vol. 33, nr 1, s. 69-81
Nyckelord [en]
conical disc refiner, energy, entropy model, fibre properties, pulp consistency, pulp properties, residence time, temperature profile, TMP
Nationell ämneskategori
Kemiteknik
Identifikatorer
URN: urn:nbn:se:miun:diva-34542DOI: 10.1515/npprj-2018-3002ISI: 000450919200009Scopus ID: 2-s2.0-85047997941OAI: oai:DiVA.org:miun-34542DiVA, id: diva2:1251472
Tillgänglig från: 2018-09-27 Skapad: 2018-09-27 Senast uppdaterad: 2018-12-11Bibliografiskt granskad

Open Access i DiVA

Fulltext saknas i DiVA

Övriga länkar

Förlagets fulltextScopus

Sök vidare i DiVA

Av författaren/redaktören
Ferritsius, RitaFerritsius, Olof
Av organisationen
Avdelningen för kemiteknik
I samma tidskrift
Nordic Pulp & Paper Research Journal
Kemiteknik

Sök vidare utanför DiVA

GoogleGoogle Scholar

doi
urn-nbn

Altmetricpoäng

doi
urn-nbn
Totalt: 341 träffar
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf