Digitala Vetenskapliga Arkivet

Endre søk
RefereraExporteraLink to record
Permanent link

Direct link
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annet format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annet språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
Selection of milling strategy based on surface integrity investigations of highly deformed Alloy 718 after ceramic and cemented carbide milling
RISE Research Institutes of Sweden, Material och produktion, Tillverkningsprocesser. University West, Sweden.ORCID-id: 0000-0003-2991-2911
GKN Aerospace Sweden AB, Sweden.
RISE Research Institutes of Sweden, Material och produktion, Tillverkningsprocesser.ORCID-id: 0000-0003-3656-1806
University West, Sweden.
2020 (engelsk)Inngår i: Journal of Manufacturing Processes, ISSN 1526-6125, Vol. 58, s. 193-207Artikkel i tidsskrift (Fagfellevurdert) Published
Abstract [en]

High speed milling with ceramic indexable inserts is a current practice for manufacturing of gas turbine components in superalloys since it allows for high material removal rates. Ceramic milling is used for rough milling, which is followed by cemented carbide semi- and finish milling. The tool motion play an important role on the resulting surface integrity. The machining strategy of up or down milling will induce different degree of residual stresses and deformations. Increased knowledge of selecting the machining strategy with lowest impact will promote improved productivity by using ceramic milling to a greater extent based on the affected depth. The main objective in this work has been to correlate the residual stresses and deformations to promote a greater utilization of ceramic milling while still producing surfaces with acceptable properties. Prior investigations have shown that ceramic milling induce very high tensile stresses in the surface, exceeding the material's nominal yield strength. A second objective has been to explain these stress levels by thorough investigations of the deformation after milling. In this study, milling tests with new and worn ceramic and cemented carbide inserts have been performed in Alloy 718. The topography, residual stresses, deformation and hardness have been investigated for up, centre and down milling. Residual stress measurements were performed using X-ray diffraction, followed by evaluation of hardness and deformation, using hardness testing, light optical microscopy as well as electron back scattering diffraction (EBSD). These results have been used to determine an appropriate milling strategy based on lowest possible impact in respect to residual stresses and deformation. The results show a high degree of deformation after milling that differs for the up, centre and down milling. Based on these results, it is shown that up milling is preferable for new inserts but as the inserts wear out, down milling becomes more suitable since a lower degree of deformation and residual stress impact was observed. EBSD and hardness testing showed that the milling, especially ceramic milling, caused severe deformation of the surfaces resulting in grain refinement to a nano-crystalline level. This is most likely the explanation for the prevalence of the high tensile stresses without distorting or causing failure. © 2020 The Authors

sted, utgiver, år, opplag, sider
Elsevier Ltd , 2020. Vol. 58, s. 193-207
Emneord [en]
Alloy 718, High volumetric milling, Material removal rate, Milling strategy determination, Residual stresses, Surface integrity, Backscattering, Carbide tools, Carbides, Ceramics industry, Deformation, Grain refinement, Hardness, Hardness testing, Nanocrystalline materials, Petroleum reservoir evaluation, Tensile stress, Topography, Well testing, Degree of deformations, Electron backscattering diffraction, Light optical microscopies, Machining strategy, Milling strategies, Nominal yield strength, Severe Deformation, Milling (machining)
HSV kategori
Identifikatorer
URN: urn:nbn:se:ri:diva-47677DOI: 10.1016/j.jmapro.2020.08.010Scopus ID: 2-s2.0-85089503058OAI: oai:DiVA.org:ri-47677DiVA, id: diva2:1463248
Merknad

Funding details: VINNOVA; Funding text 1: The results granted from the research project SWEDEMO MOTOR [2015-06047] financed by VINNOVA , Sweden’s innovation agency . Special thanks to GKN Aerospace Sweden AB and Tooltec Trestad AB. The authors also would like to thank the KK-foundation and the SiCoMaP research school .

Tilgjengelig fra: 2020-09-01 Laget: 2020-09-01 Sist oppdatert: 2023-05-22bibliografisk kontrollert

Open Access i DiVA

Fulltekst mangler i DiVA

Andre lenker

Forlagets fulltekstScopus

Søk i DiVA

Av forfatter/redaktør
Holmberg, JonasBerglund, Johan
Av organisasjonen

Søk utenfor DiVA

GoogleGoogle Scholar

doi
urn-nbn

Altmetric

doi
urn-nbn
Totalt: 35 treff
RefereraExporteraLink to record
Permanent link

Direct link
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annet format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annet språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf