Ändra sökning
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
Modeling subsurface deformation induced by machining of Inconel 718
Lund University, Sweden.
Lund University, Sweden.
Lund University, Sweden.
Linköpings universitet, Institutionen för ekonomisk och industriell utveckling, Konstruktionsmaterial. Linköpings universitet, Tekniska fakulteten.
Visa övriga samt affilieringar
2017 (Engelska)Ingår i: Machining science and technology, ISSN 1091-0344, E-ISSN 1532-2483, Vol. 21, nr 1, 103-120 s.Artikel i tidskrift (Refereegranskat) Published
Abstract [en]

Traditionally, the development and optimization of the machining process with regards to the subsurface deformation are done through experimental method which is often expensive and time consuming. This article presents the development of a finite element model based on an updated Lagrangian formulation. The numerical model is able to predict the depth of subsurface deformation induced in the high- speed machining of Inconel 718 by use of a whisker-reinforced ceramic tool. The effect that the different cutting parameters and tool microgeometries has on subsurface deformation will be investigated both numerically and experimentally. This research article also addresses the temperature distribution in the workpiece and the connection it could have on the wear of the cutting tool. The correlation of the numerical and experimental investigations for the subsurface deformation has been measured by the use of the coefficient of determination, R-2. This confirms that the finite element model developed here is able to simulate this type of machining process with sufficient accuracy.

Ort, förlag, år, upplaga, sidor
TAYLOR & FRANCIS INC , 2017. Vol. 21, nr 1, 103-120 s.
Nyckelord [en]
FEM; Inconel 718; machining; subsurface deformation
Nationell ämneskategori
Teknisk mekanik
Identifikatorer
URN: urn:nbn:se:liu:diva-136752DOI: 10.1080/10910344.2016.1260432ISI: 000395039100006OAI: oai:DiVA.org:liu-136752DiVA: diva2:1090549
Tillgänglig från: 2017-04-24 Skapad: 2017-04-24 Senast uppdaterad: 2017-04-28

Open Access i DiVA

Fulltext saknas

Övriga länkar

Förlagets fulltext

Sök vidare i DiVA

Av författaren/redaktören
Peng, Ru
Av organisationen
KonstruktionsmaterialTekniska fakulteten
I samma tidskrift
Machining science and technology
Teknisk mekanik

Sök vidare utanför DiVA

GoogleGoogle Scholar

Altmetricpoäng

Totalt: 80 träffar
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf